TM 1-1510-218-10
3-56
NOTE
There are some SID / STAR procedures
that are not suited for the operational
characteristics of the KLN 90B. These
procedures are not included in the
database.
(1)
SID and STAR procedures are stored
with the airport for which they apply. SID and STAR
procedures are accessed through the APT 7 page. If
there are both SID's and STAR's for a given airport,
then there will be two APT 7 pages, one to select a
SID and the other to select a STAR. This is indicated
by APT+7.
(2)
SID and STAR procedures are defined in
three parts: the name, the transition, and the runway
component. The APT 7 page leads the pilot through
the selection process.
ay. Selecting a SID.
1. Select the departure airport APT 7 or ACT
7 page.
2. Turn the right cursor on by pressing the
right
CRSR
button. Rotate the right outer
knob until the cursor is over the desired
SID. Press the
ENT
button.
3. The KLN 90B will now ask for the runway
in use. Position the cursor over the
appropriate runway and press the
ENT
button.
4.
The transitions are presented for
selection. Move the cursor over the
desired transition and press the
ENT
button.
5. The KLN 90B now presents a list of
waypoints that make up the SID. Review
the waypoints. Press the
ENT
button with
the cursor over LOAD IN FPL to load the
SID into the active flight plan.
6. The KLN 90B will add the SID procedure
after the airport reference point in the
active flight plan. If the airport reference
point is not included in the active flight
plan, the KLN 90B will ask to add this
waypoint to the active flight plan.
az. Selecting a STAR.
The steps required to
select a STAR are very similar to those required to
select a SID. The only difference is the order of the
steps to define the STAR and where the STAR is
loaded into the flight plan.
1. Select the APT 7 or the ACT 7 page for
the destination airport. Ensure the words,
"SELECT STAR" are displayed near the
top of the screen.
2. Turn the right cursor on by pressing the
right
CRSR
button and, if necessary,
rotate the right outer knob until the
flashing cursor is over the desired STAR.
Press the
ENT
button.
3. The KLN 90B will now ask which transition
to use.
4. In some cases, the STAR procedure
requires the selection of a specific runway.
To select a specific runway, move the
cursor over the desired runway and press
the
ENT
button.
5. The KLN 90B now presents a list of
waypoints that make up the STAR.
Review these waypoints. With the cursor
over LOAD IN FPL, press the
ENT
button
to load the STAR into the active flight plan.
The KLN 90B will then add the STAR procedure
before the airport reference point in the active flight
plan. If the airport reference point is not included in
the active flight plan, then the KLN 90B will ask to add
this waypoint to the active flight plan.
NOTE
It is not possible to load a SID or a STAR
into a flight plan other then FPL 0. SID and
STAR procedures are deleted from FPL 0
after the power is off for more than
5 minutes.
ba. Editing A SID Or A STAR.
SID and STAR
procedures have procedure headers. It is possible to
use these headers to delete and change the entire
procedure, as is done with approach procedures.
Refer to Figure 3-73. Unlike approaches, it is possible
to add and delete waypoints in SID and STAR
procedures.
Summary of Contents for C-12C
