background image

12

English

www.bedfont.com

Medi-Gas G210

Spares

Part Number 

Description

G210-CO-CAL  

Calibration kit -this contains all replacement gases, calibration  

 

tube assembly, and replacement pressure regulator

G200/10-CASE 

Carry case for personal monitoring with clear front and   

 

shoulder strap

068296/5 

Replacement moisture filters 

034 - 19 - 01000 - V 

Replacement N

Gas for calibration

034 - 21 - 01000 - V 

Replacement N

2

O (99.5%) Gas for calibration

034 - 22 - 10000 - V 

Replacement O

2

 (100%) Gas for calibration

034 - 07 - 12211 - V 

Replacement  CO

2  

(500 ppm) Gas for calibration

034 - 08 - 05010 - V 

Replacement CO (100 ppm) Gas for calibration

G210SERV 

Annual factory service and calibration

LAB411 

G210 Operating Manual

Warranty

Bedfont Scientific Ltd warrants the G210 

(batteries excepted) to be free from defects 

in materials and workmanship for a period 

of one year from date of shipment. Bedfont’s 

sole obligation under this warranty is limited 

to repairing or replacing at its choice, any 

item covered under this warranty when 

such an item is returned intact, pre-paid 

to Bedfont Scientific Limited or the local 

representative. 

Note: Sensors are guaranteed for a period 

of six months from the date of shipment from 

Bedfont.

These warranties are automatically 

invalidated if the products are repaired, 

altered or otherwise tampered with by 

unauthorised personnel, or have been 

subject to misuse, neglect or accident.

At the end of the product’s life, do not dispose of any electronic 

instrument in the domestic waste, but contact Bedfont or its distributor 

for disposal instructions.

Summary of Contents for G210
















Reviews: