manualshive.com logo in svg

Beckman Coulter SW 32 Ti, Instructions For Use Manual

Share
Download
Beckman Coulter SW 32 Ti Instructions For Use Manual Download Page 4

LXL-TB-015BB

iv

Safety Notice

Safety Information for the SW 32 Ti and SW 32.1 Ti Rotors  

procedures and methods to prevent spread of disease. Because spills may generate aerosols, 
observe proper safety precautions for aerosol containment. Do not run toxic, pathogenic, or 
radioactive materials in these rotors without taking appropriate safety precautions. Biosafe 
containment should be used when Risk Group II materials (as identified in the World Health 
Organization 

Laboratory Biosafety Manual

) are handled; materials of a higher group require more 

than one level of protection.

The rotors and accessories are not designed for use with materials capable of developing flammable 
or explosive vapors. Do not centrifuge such materials in nor handle or store them near the 
centrifuge

Although rotor components and accessories made by other manufacturers may fit in the SW 32 Ti 
and SW 32.1 Ti rotors, their safety in these rotors cannot be ascertained by Beckman Coulter. Use of 
other manufacturers’ components or accessories in these rotors may void the rotor warranty and 
should be prohibited by your laboratory safety officer. Only the components and accessories listed 
in this publication should be used in this rotor.

 

Attach all six buckets, loaded or empty, to the rotor for every run. Make sure that filled containers 
are loaded symmetrically into the rotor and that opposing tubes are filled to the same level with 
liquid of the same density. Make sure that buckets containing Quick-Seal tubes have the proper 
floating spacers inserted (if applicable) before installing the bucket cap.

If disassembly reveals evidence of leakage, you should assume that some fluid escaped the rotor. 
Apply appropriate decontamination procedures to the centrifuge and accessories.

Never exceed the maximum rated speed of the rotor and labware in use. Refer to the section on 

Run 

Speeds

, and derate the run speed as appropriate.

Do not use sharp tools on the rotor that could cause scratches in the rotor surface. Corrosion begins 
in scratches and may open fissures in the rotor with continued use.

Summary of Contents for SW 32 Ti







































Reviews:

No comments

Brands by name

Popular brands

Load more brands