manualshive.com logo in svg

Beckman Coulter SW 32 Ti, Instructions For Use Manual

Share
Download
Beckman Coulter SW 32 Ti Instructions For Use Manual Download Page 33

LXL-TB-015BB

25

SW 32 Ti and SW 32.1 Ti Swinging-Bucket Rotors

Supply List  

Other

NOTE

For MSDS information, go to the Beckman Coulter website at www.beckmancoulter.com.

Description

Part Number

Tubes and accessories

see 

Table 1

 and 

Table 2

Bucket holder rack

331186

Quick-Seal Cordless Tube Topper kit, 60 Hz

358312

Quick-Seal Cordless Tube Topper kit, 50 Hz (Europe)

358313

Quick-Seal Cordless Tube Topper kit, 50 Hz (Great Britain)

358314

Quick-Seal Cordless Tube Topper kit, 50 Hz (Australia)

358315

Quick-Seal Cordless Tube Topper kit, 50 Hz (Canada)

367803

Tube racks for the Tube Topper

for 16-mm diameter tubes
for 38-mm diameter tubes

348123
348124

OptiSeal tube rack

361646

Tube removal tool (Quick-Seal tubes)

361668

Extractor tool (

k

onical tube adapters)

354468

Spinkote lubricant (2 oz)

306812

Silicone vacuum grease (1 oz)

335148

Rotor Cleaning Kit

339558

Beckman Solution 555 (1 qt)

339555

Rotor cleaning brush

339379

Hooked O-ring removal tool

978354

Summary of Contents for SW 32 Ti







































Reviews:

No comments

Brands by name

Popular brands

Load more brands