background image

The R. W. BECKETT CORPORATION (“Beckett”) warrants to persons who purchase its “Products” from Beckett 
for resale, or for incorporation into a product for resale (“Customers”), that its equipment is free from defects 
in material and workmanship. To qualify for warranty bene

fi

 ts, products must be installed by a quali

fi

 ed service 

agency in full compliance with all codes and authorities having jurisdiction, and used within the tolerances of 
Beckett’s de

fi

 ned product speci

fi

 cations. 

To review the complete warranty policy and duration of coverage for a speci

fi

 c product, or obtain a written copy 

of warranty form 61545, please choose one of the following options:

Visit our website at: www.beckettcorp.com/warranty 
Email your request to:  [email protected]
Write to:  R. W. Beckett Corporation, P. O. Box 1289, Elyria, OH 44036

NOTE:  Beckett is not responsible for any labor cost for removal and replacement of equipment.

THIS WARRANTY IS LIMITED TO THE PRECISE TERMS SET FORTH ABOVE, AND PROVIDES EXCLUSIVE 
REMEDIES EXPRESSLY IN LIEU OF ALL OTHER REMEDIES, AND IN PARTICULAR THERE SHALL BE 
EXCLUDED THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE.  IN NO EVENT WILL BECKETT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL 
DAMAGE OF ANY NATURE.  Beckett neither assumes, nor authorizes any person to assume for Beckett, 
any other liability or obligation in connection with the sale of this equipment. Beckett’s liability and Customer’s 
exclusive remedy is limited to the cost of the product.

1.
2.
3.

Limited Warranty Information

USA:

 P.O. Box 1289 

 Elyria, Ohio 44036

Canada:

 R.W. Beckett Canada, Ltd. 

 Unit #3, 430 Laird Road 

 Guelph, Ontario N1G 3X7

www.beckettcorp.com

Part Number 6104 B24SDC R01, Printed in the U.S.A. 07/11

Summary of Contents for SDC 24 VDC

















Reviews: