Becker E12 Assembly And Operating Instructions Manual Download | Manualshive

Page: 16 / 28

background image

Deleting the limit positions using the programming unit

Connect the wires of the tubular drive to those of the same colour in the programming unit

and switch on the power supply.

Please pause for 1 sec after the last drive command before beginning the deletion se-

quence. Also leave a pause of 1 sec between the individual steps of the deletion sequence.

Deleting a limit position when 2 limit positions are programmed

Any additional functions that have been set are retained.

black

brown

blue

green-yellow

black

brown

blue

green-yellow

Programming button

Travel button

Open/close to the limit position to be deleted.

Press the programming button and keep it pressed.

Then press down the travel button and keep it pressed.

Now release the programming button, but continue to keep the travel button pressed.

Next press the programming button again.

▻

The tubular drive confirms.

►

The limit position is now deleted.

16 - en

«
...
14
15
16
17
18
...
»

Summary of Contents for E12





























Reviews:

No comments

Related manuals for E12

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 346

Brand: Kanguru Pages: 2

Brand: Kanguru Pages: 2

Brand: Fröling Pages: 44

Brand: Omron Pages: 48

XtrapulsCD1-EM-400/70

Brand: Infranor Pages: 13

XtrapulsCD1-a Series

Brand: Infranor Pages: 60

MaxOptix T5-2600P Star Series

Brand: GE Pages: 24

FRENIC-Lift LM2A Series

Brand: Fuji Electric Pages: 73

ThinkPad 73P3279

Brand: IBM Pages: 54

Brand: IBM Pages: 120

Brand: TIS Pages: 13

Brand: Tecmar Technologies Pages: 46

Brand: Teac Pages: 31

TRADFRI ICPSHC24-10EU-IL-1

Brand: IKEA Pages: 36

iPOS8015 BZ-CAT

Brand: Technosoft Pages: 34

ZAdyn4CA 018 HY

Brand: ZIEHL-ABEGG Pages: 28

TPE 1000 Series

Brand: Grundfos Pages: 220

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands