manualshive.com logo in svg

Beam RST978, Installation & User Manual, Page: 37 / 50

Share
Download
Beam RST978 Installation & User Manual Download Page 37

RST978 INSTALLATION & USER MANUAL 

37

 

Power-On Messages 

Once your phone is powered on, you may see: 

 
(Message Description) 

 

Searching...

 

The phone is attempting to establish communications with the satellite network. 
 

Registering...

 

Your phone is registering with the network. When the process is complete, you will 
see Registered. 
 

Check Signal

 

Your phone is unable to establish registration with the satellite network. Move to a 
location with a clear unobstructed view of the sky.  
 

Invalid Account

  

Contact your service provider. 
 

Enter Phone Unlock Code

 

Your phone was locked after the last use. Enter your four-digit unlock code and press 
OK to proceed.  
 

Enter PIN

 

Enter the four- to eight-digit SIM card PIN code provided by your service provider and 
press OK to proceed.  
 

Insert Card

 

Power off your phone, make sure your SIM card is inserted completely, and then 
power your phone on again. 
 

Check Card

 

The SIM card is damaged or inserted the wrong way. 
  

Blocked

 

If the SIM card PIN code is incorrectly entered three times in a row, your phone 
becomes blocked.  Use **05* to proceed to enter the PUK code. 
 

! Blocked

 

If the SIM card PIN2 code is incorrectly entered three times in a row, some features 
(e.g., Fixed Dialing) become blocked. 
 

Bad Card See Supplier

 

Your SIM card has been damaged or incorrectly issued. Contact your Service 
Provider for information. 
 

Busy Try Later 

or

 Please Try Later

 

 
The phone is unable to access the network. Try again in a few minutes. 
 

Summary of Contents for RST978



















































Reviews:

No comments