manualshive.com logo in svg

BEA ULTIMO, Manual, Page: 19 / 20

Share
Download
BEA ULTIMO Manual Download Page 19

75.0034.03 ULTIMO 20220120 

Page 19 of 20

TROUBLESHOOTING

ORANGE LED

GREEN LED

GREEN LED 
illuminates 
sporadically

The sensor is disturbed by rain 
and/or leaves.

Increase radar immunity filter and adjust the 
radar field angle.

Ghosting created by door 
movement.

Change radar field angle.

The sensor vibrates.

Check if the sensor and door header is secure.

Check position of cable and sensor cover.

The sensor sees the door 
or other unwanted moving 
objects.

Remove the objects if possible.

Change radar field size, angle, or immunity.

1

E1 - orange LED 
flashes once

The sensor signals an internal 
fault.

Replace sensor.

2

E2 - orange LED 
flashes twice

The power supply voltage is too 
low/high.

Check power supply voltage in Diagnostics 
menu (menu 3) of the LCD.

Check wiring.

3

E3 - orange LED 
flashes 3 times

Radar communication error

Check the connection at the radar.

4

E4 - orange LED 
flashes 4 times

The sensor does not receive 
enough AIR energy.

Ensure proper mounting height.

Turn on the visible red spots and adjust the 
angle of the AIR curtains.

Deactivate curtain #3 (C3, outer curtain).

5

E5 - orange LED 
flashes 5 times

The sensor receives too much 
AIR energy.

Ensure proper mounting height.

Turn on the visible red spots and adjust the 
angle of the AIR curtains.

The sensor is disturbed by 
external elements.

Eliminate the cause of disturbance (lamps, 
rain cover, etc).

8

E8 - orange LED 
flashes 8 times

AIR power emitter is faulty.

Replace sensor.

ORANGE LED is on

The sensor encounters a 
memory problem.

Cut and restore power supply. If ORANGE 
LED illuminates again, replace the sensor.

troubleshooting continues on the next page

Summary of Contents for ULTIMO





















Reviews:

No comments