manualshive.com logo in svg

BBV Ex4 MK2, Installation Manual

Share
Download
BBV Ex4 MK2 Installation Manual Download Page 32

Tx300-400-1000MK2-1000 Keypad-Ex4 MK2-TxLD Installation Guide 12Jan05.doc

  

TxLD mk2 (RS232-RS422 converter from serial number 303-0034)

 

Page 32

 

TxLD 

RS232-422 converter and keyboard line driver

 

 
The kit should contain, 
1 x DB9F – DB9F cable (SA-PL61-1), TxLD to Tx1000 matrix 
2 x TxLD units 
4 x double sided sticky pads (for mounting boxes) 

Technical Specification 

 

Power Requirements   

9-12V ac/dc 

 

Max Load 

 

 

<50mA at 12V 

 

Input

   

 

 

RS232 3 wire, Tx/Rx/Ground, DB9F 

 

Outputs

 

 

 

RS485 twin twisted pair, Green IMO connector. 

 

Facilities 

Pre-made cable provided to connect to Tx1000 base unit. 

 

TxLD powered from matrix at the base unit.  
TxLD powered from keyboard’s PSU at remote end. 

 

 

Box dimensions

 Width: 

 

58mm 

 Length: 

 

83mm 

 Height: 

 

27mm 

 

Compatible Equipment

 

Tx1000 series base units/keyboards, RS232 serial extension of BBV 
compatible equipment. 

 

Most 3 wire RS232 links can be extended. 

 

Temperature range 

-10

°

C to +40

°

C 

 

INTRODUCTION 

The TxLD is a simple to install, cost effective device for remote installation of a BBV Tx1000 Slave Keyboard 
when the cable length for the keyboard serial data exceeds 50 metres. The communications data for the 
keyboard is RS232, which will become unreliable at distances greater than 50M. The TxLD converts the 
RS232 data to 4 wire RS422 and then back to RS232 at the opposite end, this enables the data to be 
transmitted over cable lengths up tp 1200M. The TxLD’s are supplied with sticky pads for easy wall 
mounting. 
 

INSTALLATION  

Mount the units in relevant positions close to the Tx1000 Base Unit and the Slave Keyboard, and 
interconnect both units with twin twisted pair cable. Note that at the keyboard the TxLD uses the 
Tx1000/KBD slave keyboard power supply and at the matrix the TxLD is powered from the Tx1000 via the 
supplied cable. 
  

Line Length 

The TxLD will perform optimally over any length of cable up to 1200M using the recommended cable type 
“BELDEN 9502”. Cables are easily connected to the 5 pin plug/socket screw connector, which plug into the 
socket on the end of the unit. Ensure cable run is away from sources of interference and high current 
carrying cables.  

 
IMO Connectors 

Connection of the twin twisted pair wires to the TxLD units is made 
via the green IMO connectors located at the opposite end of the TxLD 
to the D-type. It is important to maintain correct polarity and ensure 
that RX and TX cross over. 

GND

TB/-(OUT)

TA/+(OUT)

RA/+(IN)

RB/-(IN)

Summary of Contents for Ex4 MK2





































Reviews:

No comments

Brands by name

Popular brands

Load more brands