background image

11

WWW.BBTA.COM.AU

BBT-BC-36CCBH, BBT-BC-36CCDH

Read the Owner’s Manual carefully. Be thoroughly 
familiar with the controls and proper use of the unit. 

NEVER allow anyone to use the unit without proper 
instruction. Be sure the operator wears the correct 
foot, leg, eye, face and hearing protection.

DO NOT rely on the debris shield on the unit to protect 
your eyes from ricocheting or thrown objects. Keep the 
area clear of bystanders, children and pets. 

NEVER allow children to operate or play with the unit.

DO NOT allow anyone to enter the operating DANGER 
ZONE
 with you. The danger zone is an area 15 metres 
in radius (about 16 paces) or 50 feet.

Persons in the RISK ZONE beyond the danger zone are 
advised to wear eye protection from flying objects. If 

the unit must be used where there are unprotected 
people, operate at a low throttle speed to reduce the 
risk of thrown objects.

Move the stop switch to “STOP” position when the 
engine idles, ensure unit is reliable before cutting.

Only continue to operate the unit when stop switch is 
in good working condition, routine checks for this, is if 
the cutting attachment stops turning when the engine 
idles.

RULES OF SAFE OPERATION

Danger Zone - An Area 15 Metres in Radius

In addition to wearing head, eye, face and ear 
protectors, ensure you wear shoes that protect 
your feet and improve your footing on slippery 
surfaces. Do not wear ties, jewellery, or loose 
dangling clothing which could get caught in the 
unit.

DO NOT wear open-toed footwear or go bare-
foot or bare-legged. In certain situations, you 
must wear total face and head protection. Pay 
attention not to kick back and blade thrust.

    WARNING

All models of trimmers and Brush Cutters can 
throw small stones, metal and other small objects 
as well as the material being cut. Read these Rules 
of Safe Operation
 with care.

    WARNING

NO PERSON EXCEPT OPERATOR ALLOWED WITHIN 15 METRES RADIUS DANGER ZONE. EYE, EAR, FACE, 
FOOT, LEG AND BODY PROTECTION MUST BE WORN BY OPERATOR. PERSONS IN ZONE OR RISK AREA 
BEYOND DANGER ZONE SHOULD WEAR EYE PROTECTION AGAINST THROWN OBJECTS. RISK DIMINISHES 
WITH DISTANCE FROM DANGER ZONE.

15M

Summary of Contents for BBT-BC-36CCBH



























Reviews: