BAYCO • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • www.baycoproducts.com
INS-1022-12
500 Watt Halogen Work Light
Important safety instructions
WARNING: Read all instructions carefully
SAVE THESE INSTRUCTIONS
CAUTION: RISK OF ELECTRICAL SHOCK
Do not use with extension cord near water or where water may
accumulate.
Keep plugs and receptacles dry.
For use only on GFCI protected circuits.
Risk of burns, do not operate without guard. (See assembly instructions.)
Lighted lamp is hot. Keep away from combustibles. Unplug to change
bulb. Do not touch bulb
WARNING RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE
TO EXCESSIVE UV RADIATION OR INJURY TO PERSONS
Unit operates on 120V AC 60 Hz only
Unplug and allow cooling before replacing bulb.
Bulb gets HOT quickly
Do not touch hot lens guard or enclosure.
Do not remain in light if skin feels warm.
Do not look directly at lighted lamp.
Keep lamp away from materials that may bum.
Use only with a 500 Watt or smaller type T bulb.
Do not touch the bulb at any time; use a soft cloth or gloves. Oil from skin
may damage bulb.
Do not operate the lamp with missing or damaged guard, lamp
containment barrier or UV light filter.
SAVE THESE INSTRUCTIONS
WARNING: When using outdoor use work lights, basic safety precautions
should always be followed to reduce the risk of fire, electrical shock, and
personal injury, including the following:
Use only three-wire outdoor extension cords that have three-prong
grounding plug and receptacles that accept the appliance's plug.
Ground Fault Circuit Interrupter (GFCl) protection should be provided on
the circuit(s) or outlet(s) to be used for the wet location work light.
Receptacles are available having built-in GFCI protection and are able to
be used for this measure of safety.
Use only an extension cord for outdoor use, such as an extension cord of
cord type SW, SW-A, SOW, SOW -A. STW, STW-A, STOW. STOW-A.
SlW, SlW-A. SlOW. SlOW-A. SJTW. SJTW-A. or SJTOW, SJTOW-A.
BULB INSTALLATION AND REPLACEMENT
DO NOT TOUCH BULB WITH BARE HANDS
1.
Turn the light off and unplug from the power source.
2.
Allow the fixture to fully cool before proceeding.
3.
Always wear gloves or use a clean cloth to handle bulb. The natural oil
from skin will leave a residue that will cause the light to burn out
immediately.
4.
To remove the lens cover, remove the retaining screw on the front of the
lens cover. The lens cover will then swing open exposing the bulb.
5.
To remove the bulb, grip one end of the bulb and gently push towards the
other end and pull outward to release the bulb.
6.
Using a clean cloth or wearing gloves to hold the bulb, gently insert one
end of the bulb into the receptacle and press firmly into place. Place the
other end of the bulb into the opposite receptacle and gently press into
place. Make sure bulb is seated properly.
7.
Close the lens cover and replace the retaining screw.
8.
Do not test light without lens cover properly attached.
WARNING: Read all instructions carefully
SAVE THESE INSTRUCTIONS
CAUTION: RISK OF ELECTRICAL SHOCK
WARRANTY
PRODUCTS COVERED UNDER THIS LIMITED WARRANTY:
This product is warranted to the original purchaser for 1 year and only covers
failures due to defects in materials or workmanship. If this product is used for
rental purposes, the warranty term is reduced to 90 days from the date of
purchase.
NOT COVERED
The warranty does not cover normal wear and tear or cosmetic damage. The
Limited Warranty also does not cover damages which occurred in shipment or
failures which are caused by accidents, misuse, abuse, faulty installation and
lightning damage. Consequential damages, incidental damages or incidental
expenses, including damage to property. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, which may vary from state to state. This warranty does not apply to
certain Bayco professional products that carry a specific warranty unique to
those products.
WARRANTY CLAIMS - USA
Contact Bayco for USA warranty claims. Call 800-233-2155 and Bayco
Customer Service will provide a Return Goods Authorization (RGA) to facilitate
rapid warranty action. After receiving the RGA, send the product (shipping
prepaid) to BAYCO • 640 S. SANDEN BLVD • WYLIE, TEXAS • 75098. Include
a dated proof of purchase and a brief description of the defect with your name,
address and phone number. Your product will either be repaired or replaced at
the option of Bayco and returned as soon as practical, but no later than 45
days after being received by Bayco.
WARRANTY CLAIMS - CANADA
Return the product to the place where purchased with a dated proof of
purchase and a brief description of the defect with your name, address and
phone number. Your product will either be replaced or purchase price
refunded.
REQUEST FOR WARRANTY ACTION
If you have any questions about this warranty or any other Bayco product
inquiries contact BAYCO • 640 S. SANDEN BLVD • WYLIE, TEXAS • 75098 or
call 800-233-2155
