Bay Networks 58000 Installation And Reference Manual Download Page 125

Page: 125 / 158

Using the System Configuration Menus

893-878-B

6-19

Modifying Port Configurations

You can configure the ports on the Model 58000 switch to operate in various
modes.

Table 6-6

lists and describes the port configuration options available for

10 Mb/s and 100 Mb/s ports. For detailed descriptions of port configurations,
refer to

Chapter 2

,“Planning a Switched Network.”

Modifying Port Duplex Mode

To modify the duplex mode for a switch port, follow these steps:

Choose Configuration Parameters from the Main Menu.

The Configuration Parameters menu is displayed.

Choose Switch Parameters from the Configuration Parameters menu.

The Switch Parameters menu is displayed.

Choose Modify Switch Port Speed and Duplex Mode from the Switch
Parameters menu.

A Switch Port Speed and Duplex Mode menu similar to that shown in

Figure 6-9

is displayed.

Table 6-6.

Port configuration options

Port speed

Configuration options

10 Mb/s
(Switch front
panel ports)

Duplex mode—ports can operate in half-duplex mode or full-duplex
mode. (First 12 ports can only operate in half-duplex mode when
connected to the Model 500x backplane.)

Front/back connection—first 12 ports can be configured for either
front connection or backplane connection.

Port type mode—ports can operate in automatic mode or forced
feeder mode.

100 Mb/s
(MDA ports)

Duplex mode—ports can operate in half-duplex mode or full-duplex
mode.

Port type mode—ports can operate in automatic mode or forced
feeder mode.

Flow control—Flow control can be enabled or disabled on ports
operating at 100 Mb/s in the full-duplex mode.

893-878-B Book Page 19 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands