Bay Networks 58000 Installation And Reference Manual Download Page 111

Page: 111 / 158

Menu Overview

893-878-B

6-5

Menu Header

The menu header is at the top of the menu and includes switch system
information.

Table 6-2

briefly describes the system information included in the

menu header.

The System Information menu provides an extensive list of system
information. Refer to

Displaying System Information

later in this chapter for

instructions on how to display the System Information menu.

Command and Status Area

The command and status area makes up the middle portion of the menu. This
part of the menu includes the title of the menu and a list of status information
and/or a list of commands.

Command Line

The command line at the bottom of every menu includes the following
commands for interacting with the system:

•

Up and down arrow keys to move cursor (cursor moves as a highlight
box).

•

[Enter] to select the highlighted menu item or complete a text input.

•

[Ctrl]+P to return to main menu.

Table 6-2.

Menu header information

Item

Description

Header title

Displays the model number or product name for the
Model 58000 switch.

System Up Time

The time elapsed since last power up or reset.

MAC Address

The 6-byte MAC address of the Model 58000 switch
(hexadecimal notation).

Switch Software
Version

The release software version.

IP Address

The IP address of the Model 58000 switch. The letter (M) after
the IP address indicates that this is a master switch.

Default Gateway

The IP address of the default gateway for the Model 58000
switch.

Subnet Mask

The IP subnet mask for the Model 58000 switch.

893-878-B Book Page 5 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands