Bay Networks 58000 Installation And Reference Manual Download Page 115

Page: 115 / 158

Using the System Configuration Menus

893-878-B

6-9

Displaying System Information

The System Information menu provides the following information:

•

The current switch configuration

•

Configurations for 10 Mb/s and 100 Mb/s ports

•

Which ports are operating as trunk ports

To display the System Information menu, choose System Information from the
main menu. A System Information menu similar to that in

Figure 6-4

displayed.

Figure 6-4.

System Information menu

Bay Networks 58000 Ethernet Switch Module

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

System Information

Switch Firmware Version [None]

Switch Mode [Basic]

Memory (Boot/Flash/NVRAM/DRAM) [128K/2048K/256K/4096K]

Master Switch Priority [8000]

Master Switch MAC Address [000081000201]

Master Switch IP Address [134.177.32.98]

100 Mb/s Full Duplex (Port#) [MDA P1]

100 Mb/s Half Duplex (Port#) [MDA P2]

10 Mb/s Full Duplex (Port#) [None]

10 Mb/s Half Duplex (Port#) [1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16]

Trunk Ports [MDA P1]

The current firmware version.

<CTRL><P>:Main Menu <CTRL><U>:Previous Menu <CTRL><L>:Refresh Screen

893-878-B Book Page 9 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands