background image

11

8. MAINTENANCE - SAFETY VALVES

8.1  The pressure relief valve and any other safety valves fitted should be regularly 

checked for correct operation.

8.2  Manually operate the valve(s) and ensure that water flows freely from the valve 

and through the discharge pipe. NOTE the water discharged may be very hot. 

Ensure the valve re-seats correctly when released.

9. USER INSTRUCTIONS

9.1  The 

BAXI Premier Plus water heater

 stores water at the temperature set on the 

adjustable thermostat. This is factory set to give a storage temperature of approx. 

60

o

C. However, this can be set to give temperatures in the range 10

o

 to 70

o

C. The 

adjustable thermostat is located on the front of the cylinder.

9.2  To avoid any risk of freezing when the water heater is not in use for long periods 

during the winter months, do not switch off the boiler or immersion heater and set 

the control thermostat to its minimum position. NOTE this will not protect other 

parts of the system pipe work.

9.3  To ensure the water heater continues to operate at its optimum performance it 

should periodically be maintained in accordance with the instructions given under 

the sections headed MAINTENANCE.

9.4  IMPORTANT NOTES TO THE USER

• 

Do not block or restrict the discharge from any safety valve fitted

• 

Do not tamper with any safety valve fitted

• 

Do not bypass the thermal cut-outs in any circumstances

• 

If a fault is suspected contact a qualified engineer to check the system

10. GUARANTEE

10.1  This water heater is guaranteed for a period of 10 years from the date of 

purchase with the exception of the thermal controls which are guaranteed for a 

period of two years provided:

10.2  The water heater has been installed in accordance with these instructions and 

all necessary inlet controls and safety valves have been fitted correctly.

10.3  Any valves or controls are of the manufacturers recommended type.

10.4  The water heater has not been tampered with and has been regularly 

maintained as detailed in these instructions.

10.5  The water heater has been used only for heating potable water.

10.6  The water heater is NOT guaranteed against damage by frost or due to build up 

of scale.

10.7  This guarantee does not affect the statutory rights of the consumer.

Summary of Contents for PREMIER PLUS 1000L





















Reviews: