921.968.2.00.02.010702
19
Afstand til brændbart matr. skal være som Gasreglementet foreskriver
vedr. aftrækskanal (afsnit 5.5) Det vil bl.a. sige:
•
Der skal overalt være en afstand på mindst 50 mm fra yderkant røgrør
til brændbart materiale.
•
Aftræksrøret SKAL isoleres med min. 25 mm mineraluld* fra og med
første murgennemføring til og med afslutning.
•
Mineraluldsisoleringen skal føres med igennem brændbart matr. og
evt. slutte min. 100 mm herfra.
•
“Vandrette” aftræksrør skal føres med min. 5 promille fald mod kedel
eller mod kondensfang.
•
Det “vandrette” luftindtagsrør nærmest murrist skal føres med min. 5
promille fald udad - bort fra kedlen.
OBS: Der er afstandskrav fra udvendig aftræksrør til brændbart matr.
•
25 mm mineraluldsisolering medleveres ikke fra
BAXI
.
NB:
Ved aftrækslængde over 3 meter i skorstenen anbefales installation
af kondensfang
Ved montage i afmeldt skorsten skal der i skorstensvangen etableres
en service-/renselem, der muliggør afmontering af svømmeren i
underparten for rensning/service.
SPLIT AFTRÆK MED RØGAFTRÆK OVER TAG
System S3 og S4
Hvor forholdene taler herfor anvendes SPLIT aftræk hvorved forstås at
luften tages ind i et rør og røggas ledes ud over tag i et andet.
Tilslutningssæt består af:
1 stk. tilslutningssæt Ø80
Desuden skal bruges:
•
Luftindtag og hætte
•
Top til skorsten
•
Lige rør til luft eller røggas (Til røggas skal anvendes rustfri rør, til luft
anvendes aluminiumsrør)
•
Max totallængde af splitaftræk = 20 m minus 1 m for hver 90
°
bøjning
(0,5 m pr. 45
°
bøjning)
•
Bøjning 45
°
eller 90
°
(Til røggas anvendes rustfri, til luft anvendes
aluminium)
•
Silikone
•
Rørbærer for røgrør og luftrør
•
Loftskrave for afslutning mod loft.
•
1 stk. Taginddækning
Montage af lodret SPLIT
• Split tilslutningssættet monteres
på kedlen som anført andetsteds i
denne instruktion.
NB: Luftindtag skal tages fra det fri
eller fra ventileret loftrum på min.
70 m
3
.
Luftindtag/røgafgang - SPLIT
Luftindtag (Til luft anvendes
aluminiumsrør)
S
4
: Luftrist fastgøres med de med
flg. rawlplug og rustfri skruer
udvendig på mur. Der tætnes evt.
omkring rist med silikone.
S
3
: Luft fra uudnyttet tagrum på
min. 70m
3
. Medflg. luftrist
anvendes ovenpå røret.
1. Luftrørsinstallationen føres fra
luftrist til kedlens luftindtag.
010725_0100
Distance from flammable materials must be as laid down in the Gas
Regulations regarding a flue duct (section 5.5), that is to say:
•
On all sides there must be a clearance of at least 50 mm from the outer
edge of the flue pipe to flammable materials.
•
The flue pipe MUST be insulated with a minimum of 25 mm mineral
wool* from and including the first wall duct up to and including the
end.
•
The mineral wool insulation must be taken through the flammable
material and, if necessary, end at least 100 mm from it.
•
“Horizontal” flue pipes must be installed with a fall of at least a 5‰
towards the boiler or towards the condensation trap.
•
The “horizontal” air intake pipe next to the wall grating must have a fall
of at least 5‰ outwards – away from the boiler.
NOTE: There are criteria for the distance from an external flue pipe to
flammable materials.
•
25 mm mineral wool insulation is not supplied by
BAXI
.
NB:With flue lengths over 3 metres in the chimney, we recommend fitting
of a condensation trap. In the case of installation in a disused chimney,
a servicing / cleaning door must be fitted in the chimney jamb, allowing
dismantling of the float in the lower part for cleaning / servicing.
SPLIT FLUE WITH FLUE OUTLET VIA THE ROOF
S3 and S4 System
Where indicated by the conditions, use the SPLIT flue, which means that
the air is taken in via one pipe and the flue gas is directed out above the
roof in another pipe.
The connecting set consists of:
1 connecting set Ø 80
In addition, the following must be used:
•
Air intake and cover
•
Cap for the chimney
•
Straight pipe for air or flue gas (use a rust-resistant pipe for flue gas, an
aluminium pipe for air)
•
Maximum total length of split flue = 20 m minus 1 m for each 90
°
bend
(0.5 m for each 45
°
bend)
•
45
°
or 90
°
bend (use rust-resistant for flue gas, aluminium for air)
•
Silicone
•
Pipe clamps for flue pipe and air pipe
•
Ceiling flange for end against the ceiling
•
1 roof flashing
Installation of vertical SPLIT
•
Fit the split connecting set to the boiler
as shown elsewhere in these instruc-
tions.
NB:The air intake must be taken from the
open air or from a ventilated loft of at
least 70 m
3
.
Air intake / flue outlet – SPLIT
Air intake(Use aluminium for air)
S
4
: Secure air grating to the outside of the
wall using the Rawlplugs and rust-resis-
tant screws provided. If necessary, seal
around the grating with silicone.
S
3
: Air from an unused loft of at least 70 m
3
.
Use the air grating provided on top of the
pipe.
1. Take the air pipe installation from the air
grating to the air intake of the boiler.
Insulated flue pipe with cover
Isoleret røggasrør m/hætte
Roof flashing
Taginddækning
25 mm insulation
* Aluminium laminated mat
Isolering 25 mm
* Alu. Lamelmåtte
Ceiling flange
Loftskrave
Pipe Ø80 (rust-resistant)
Rør Ø80 (rustfri)
Vertical connecting set
Split tilslutningssæt
Pipe Ø 80 (Alu.)
Rør Ø 80 (Alu.)
Wall grating
Murrist
Silicone
Silicone
Wall bush
Murbøsning
Summary of Contents for NUVOLA 28 Fi
Page 37: ...921 968 2 00 02 010702 37 ...
Page 38: ...921 968 2 00 02 010702 38 ...
Page 39: ...921 968 2 00 02 010702 39 ...