37
I
N
S
T
A
L
L
E
R
S
e
c
t
i
o
n
(
e
n
)
7690785.01 (1-05/18)
12. INITIAL IGNITION - SPECIAL FUNCTIONS
When the boiler is powered up, the code “311” appears on the display and the boiler is ready for “initial ignition”.
Follow the procedure “GAS EXTRACTION FUNCTION” as described in the section below and enable programme 312.
After this operation, the boiler is ready to ignite the burner.
'XULQJWKLVSKDVHLWLVUHFRPPHQGHGWRNHHSWKHSUHVVXUHLQWKHV\VWHPDWDYDOXHEHWZHHQDQGEDU
12.1 SYSTEM GAS EXTRACTION FUNCTION
7KLV IXQFWLRQ LV XVHG WR IDFLOLWDWH WKH HOLPLQDWLRQ RI WKH DLU LQVLGH WKH KHDWLQJ FLUFXLW ZKHQ WKH ERLOHU LV ¿UVW LQVWDOOHG RU DIWHU
maintenance when the water is drained from the primary circuit.
To enable the system gas extraction function press buttons
together for 6 seconds. When the function is active,
On
appears on the display for a few seconds, followed by programme row
312
.
The electronic board will activate a pump on/off cycle lasting 10 minutes. The function will automatically stop at the end of the
cycle. To manually exit this function, press the above buttons together for 6 seconds once again.
12.2 CALIBRATION FUNCTION
To calibrate the gas valve, proceed as follows:
• Press buttons
and
together for at least 6 seconds. When the function is enabled, the displays shows “
On
” for a few
seconds followed by programme row “
304
” alternated with the % of boiler power.
• Press
to gradually adjust power (sensitivity 1%).
• To exit press both buttons together for at least 6 seconds, as described in point one
Press
WRGLVSOD\WKHLQVWDQWDQHRXVÀRZWHPSHUDWXUHIRUVHFRQGV
12.3 CHIMNEY SWEEPER
When this function is enabled, the boiler generates maximum heating power. To enable the function, proceed as follows:
• press
together for 6 seconds. The display shows "
303
" alternated with the power output of the boiler.
• Press
and
to adjust boiler power
1
PLQLPXP
2
PD[LPXP'+:
3
PD[LPXPKHDWLQJ
• To interrupt the function repeat the procedure described in point one.
13. FAULTS THAT CANNOT BE RESET BY THE USER
In case of
FAULTS
that cannot be reset by pressing
(such as E151, E162 or exceeding
5 manual RESET attempts by the user) RESET the board by pressing the black button (
R
)
located under the rubber cap (symbol
RIWKHIURQWFRQWUROSDQHO¿JXUHWRVLGH
Summary of Contents for LUNA DUO-TEC MP+ 1.115
