manualshive.com logo in svg

Baxi 5130243, Kit Instructions

Share
Download
Baxi 5130243 Kit Instructions Download Page 46

17.0

Fault finding

46

© Baxi Heating UK Ltd 2011

17.1

Failures with error message

Some system failure modes can be recognised by the solar
differential temperature controller and will be 
indicated by an error message on the controller display. Refer
to the table below for details of possible errors and suggested
measures to rectify.

Error representation on display Possible reasons

Measures

flashing

• Sensor wire broken

• Check wire

• Sensor defect

• Check sensor resistance, if necessary exchange sensor

flashing

• Short circuit in sensor wire

• Check wire

• Sensor defect

• Check sensor resistance, if necessary exchange sensor

• Error in pump connection

• Check cabling

• Pump defect

• Exchange pump

• Air in the system

• Check the float of the flow meter moves

when the system runs (if visible)

• Connection with flow 

• Check wire

meter defect

• Sensor wire broken

• Check wire

• Sensor defect

• Check sensor resistance, if necessary exchange sensor

!
!

!

+

Circulation error:  no flow

Additionally at energy
productivity measurement:

flashing

Summary of Contents for 5130243





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands