Baumuller BUM 62 Operating Instructions Manual Download Page 46

Page: 46 / 74

Installation

Mono Power Unit BUM 62, 63, 64

5.94005.12

Baumüller Nürnberg GmbH

5.6.3 Control terminal

Sub-unit terminal X99A/X99B

Due to the connection of X99A to the X99B of the next BUS-device in the chain, the system can execute
the signals as a bus connection.

Recommended connection length 44 mm

WARNING

All the control voltages connected from outside must be PELV or SELV.

Terminal no.

Assignment

1, 2

+ 24 V (PELV)

Terminal for power supply to the units,

both terminals internally connected,

2nd terminal with power supply current > 10 A

3, 4

Ground 24 V (PELV)

Terminal for power supply to the units,

both terminals internally connected,

2nd terminal with power supply current > 10 A

BB int (PELV)

Ready for use signal form the supply converter to all units

connected to the DC link

Reserved (message ballast) (PELV)

if no ballast unit is used the terminal 6 must be connected

with terminal 1 or 2 (+24 V)

Summary of Contents for BUM 62











































































Search results

Summary of Contents for BUM 62

Reviews:

Related manuals for BUM 62

Brands by name

Popular brands

Baumuller BUM 62, Operating Instructions Manual

Search results

Summary of Contents for BUM 62

Reviews:

Related manuals for BUM 62

Brands by name

Popular brands