manualshive.com logo in svg

Baumer DAB10, Operating Manual, Page: 50 / 56

Share
Download
Baumer DAB10 Operating Manual Download Page 50

8

 | 

Preventive maintenance

Baumer

50

Operating Manual

DAB10, DST53, DST76 | V3

8

Preventive maintenance

The sensor is maintenance-free. No special preventive maintenance is required. Regular clean-
ing and regular checking of the plug connections are recommended.

8.1

Cleaning the device

Exterior cleaning

When cleaning the exterior of the device, make sure to use cleaning agents that do not affect
the housing surface and seals.

NOTICE

Material damage due to improper cleaning.

Unsuitable cleaning agents and methods can cause leaks and damage the device, the seals, or
the connections.

a) Always check the suitability of the cleaning agent for the surface to be cleaned.

b) Do not use scouring agents, solvents, or other aggressive cleaning agents.

c) Do not use jets of liquid for cleaning, for example, a high-pressure cleaner.

d) Do not scrape off contamination with sharp-edged items.

Interior cleaning

No interior cleaning of the device is required.

Summary of Contents for DAB10

























































Reviews:

No comments