background image

Troubleshooting 
 

IMPORTANT: If your cooker hood appears not to be operating 
properly, before contacting the Baumatic Customer Care 
Department, please refer to the checklist below. 

 

 

My cooker hood will not start. 

 
 

o

 

Check that the hood is connected to the electricity supply 

 

o

 

Check that the fan speed control is set correctly. 

 

 

My cooker hood is not working effectively. 
 
 

o

 

The fan speed is not set high enough 

 

o

 

The grease filters are dirty and require cleaning. 

 

o

 

The kitchen is not well ventilated enough. 

 

o

 

If the hood is set up for recirculation mode, check that the 
carbon filters do not need replacing. 

 

o

 

If the hood is set up for extraction mode, check that the ducting 
hose and discharge outlet are not blocked. 

 

 

My cooker hood has switched off during operation. 
 
 

o

 

The safety cut-out device has been tripped. 

 

o

 

Turn off the hob and then wait for the safety cut-out device to 
reset. 

 

o

 

IMPORTANT:  If you have installed your cooker hood too low, 
the safety cut-out device will frequently trip. Your cooker hood 
may become damaged if the safety cut-out device is tripped 
frequently. 

 
 
 
 
 
 

 

24

Summary of Contents for BE605BGL





























Reviews: