Bastl Instruments Little Nerd Page 12 Assembly Manual Download

Page: 12 / 12

Before you connect anything, make sure that your system is disconnected from power. Also double

check the polarity of the ribbon cable, the red cable should match the 12V rail both on the module and

on the bus board!

TROUBLESHOOTING

This may be the common problems and solutions:

Inputs don’t work as they should

Check out the soldered joints again. If needed heat up them and add a bit of solder.

See the installed positions of jumpers (see page 11)

Check out the ICs orientation (see page 9)

RGB LED is not working how it should

Is it oriented the right way? (see page 6)

If you are having some more trouble, the best thing is to take a nap! Especially late at night!

If you are still in trouble, you can send the detailed description of the problem with enclosed

highresolution photos on

diy@bastlinstruments.com

If you think that you are unable to make the module work on your own, consider our “

Come to Daddy

”

service.

Summary of Contents for Little Nerd













Search results

Summary of Contents for Little Nerd

Reviews:

Related manuals for Little Nerd

Brands by name

Popular brands

Bastl Instruments Little Nerd, Assembly Manual

Search results

Summary of Contents for Little Nerd

Reviews:

Related manuals for Little Nerd

Brands by name

Popular brands