background image

PAGE 2

Basta Boatlifts are protected by one or more US Patents   

www.gobasta.com/patents

DANGER

 

•  Do not exceed the maximum weight capacity specified for the lift. Maximum weight                 

 

    capacity can be found on the cover of this manual and on the H frame of the lift. 

 

    Improper use or failure to follow this instruction can cause property damage,  

 

    serious injury, or death.

 

•  Never use for lifting humans or animals. Improper use or failure to follow this  

 

    instruction can cause property damage, serious injury, or death. The lift should only  

 

    be used for lifting boats & watercraft.

 

•  Always avoid being under, and maintain adequate clearance from, the lift.  Failure to  

 

    follow this instruction can cause serious injury or death. 

 

•  Always use AGM batteries and follow battery manufacturer’s warnings and instructions.  

 

    Improper use, or use of other batteries, have the potential to produce flammable hydrogen  

 

    gas which can result in serious injury or death. 

 

•  Visually inspect all parts and assemblies for damage or defects prior to assembling lift.

 

•  Install the lift on firm and level ground.

 

•  Verify the lower frame of the lift is level before each use.

 

•  Do not play on or near the lift. 

 

•  Do not service the unit with the watercraft on the lift. 

 

•  High pressure hydraulics can penetrate skin. Oil injected into the skin from  

 

    high pressure systems can cause severe injury. In the case of injury, seek  

 

    medical attention immediately.

WARNING

 

•  Do not install the lift alone.

 

•  The lift should only be used for lifting boats & watercraft.

 

•  Passengers should stand clear of the lift when the lift is in operation. 

CAUTION

Summary of Contents for Over-Center 4.5k37

























Reviews: