background image

PAGE 20

FOB POWER-UP

After turning on the ON/OFF switch in the dock box, the fob 

receiver requires a 5 second delay before the fob is enabled. 

FOB OPERATION

Depress the unlock button (lower right), this will allow normal 

operation of the fob. The lockout is re-enabled after 60 

seconds without a button press. Lift operation using the fob 

is limited to 120 seconds of continuous operation. If a longer 

cycle is needed it is necessary to release button and then 

re-depress.

FOB PROGRAMMING

1.  

Turn off the ON/OFF switch.

2. 

Wait 20 seconds.

3.

 

Turn power back on, and within 5 seconds of    

     power on, press both the UP and DOWN buttons  

     on the fob simultaneously for 1 second then  

     release.

4. 

Repeat steps 1-3 for additional Fobs. Up

     to four fobs may be enrolled. If a fifth fob 

     is enrolled, the first enrolled fob will fall off the list. 

BATTERY REPLACEMENT

Fob uses CR2032, 3 volt battery, commonly found online or at 

drug / hardware stores. Part numbers vary by manufacturer.

LOW BATTERY LOCKOUT

The remote control contains a low voltage lockout which 

is intended to protect the lift’s battery from over-discharge. 

When the battery drops below the low battery threshold 

during operation, further use of the fob is not allowed. The 

manual UP/DOWN switches will allow the lift to operate 

when sufficient battery power is present. The lift should 

be checked and charged prior to further operation.

TROUBLESHOOTING

If fob worked previously, but 

does not currently, replace fob 

battery or verify fob battery 

has greater than 3v. If fob does 

not work after replacement 

of fob battery, load test lift 

battery ensuring voltage does not drop below 11v while 

in use. If you have questions, contact your local dealer or 

Basta Boatlifts.

UNDERWATER LIGHTS

The underwater lights are activated whenever the

lift is operated. The lights stay on for 2 minutes 

after the lift is operated. The lights may be 

manually turned on or off by depressing the lower 

left button on the remote fob. When manually enabled the 

lights will automatically turn off after 

4 minutes. This prevents accidental battery discharge.

REMOTE CONTROL FOB INFORMATION

Summary of Contents for Over-Center 4.5k37

























Reviews: