Basler BE1-50/51B-229 Instruction Manual Download Page 9

Page: 9 / 57

9252000892 Rev A

BE1-50/51B-229 General Information

SECTION 1

•

GENERAL INFORMATION

TABLE OF CONTENTS

SECTION 1

•

GENERAL INFORMATION ................................................................................................ 1-1

INTRODUCTION.................................................................................................................................... 1-1

FEATURES ............................................................................................................................................ 1-1

Advantages......................................................................................................................................... 1-1

APPLICATION ....................................................................................................................................... 1-2

SPECIFICATIONS ................................................................................................................................. 1-2

Current Sensing Input ........................................................................................................................ 1-2

Time Overcurrent (51) Element.......................................................................................................... 1-2

Instantaneous Overcurrent (50) Element ........................................................................................... 1-4

Burden ................................................................................................................................................ 1-5

Frequency Response ......................................................................................................................... 1-6

Transient Response ........................................................................................................................... 1-6

Harmonic Response........................................................................................................................... 1-6

Target Indicators ................................................................................................................................ 1-7

Output Contacts ................................................................................................................................. 1-7

Type Tests.......................................................................................................................................... 1-7

Environment ....................................................................................................................................... 1-8

Agency Recognition ........................................................................................................................... 1-8

Physical .............................................................................................................................................. 1-8

Patent ................................................................................................................................................. 1-8

Figures

Figure 1-1. Integrating Reset Characteristic Curve ................................................................................... 1-4

Figure 1-2. Instantaneous Characteristic Curves ...................................................................................... 1-5

Figure 1-3. Harmonic Rejection................................................................................................................. 1-7

Figure 1-4. BE1-50/51B-229 Burden Characteristics ................................................................................ 1-6

Tables

Table 1-1. Type SFC Relays Suitable for Direct Replacement ................................................................. 1-1

Table 1-2. Time Characteristic Curve Constants with SW3-3 Open (Off)................................................. 1-3

Table 1-3. Time Characteristic Curve Constants with SW3-3 Closed (On) .............................................. 1-3

Summary of Contents for BE1-50/51B-229


























































Search results

Summary of Contents for BE1-50/51B-229

Reviews:

Related manuals for BE1-50/51B-229

Brands by name

Popular brands

Basler BE1-50/51B-229, Instruction Manual

Search results

Summary of Contents for BE1-50/51B-229

Reviews:

Related manuals for BE1-50/51B-229

Brands by name

Popular brands