Basler BE1-50/51B-229 Instruction Manual Download Page 17

Page: 17 / 57

9252000892 Rev A

BE1-50/51B-229 General Information

1-7

Figure 1-4. Harmonic Rejection

Target Indicators

Gravity latched, manually reset targets indicate that current of 0.2 amperes or greater was present in the
trip circuit. Target coil resistance is less than 0.1 ohms and operate time is less than one millisecond. See

Output Contacts

for maximum current rating.

Output Contacts

Output contacts are surge protected and rated as follows.

Resistive Ratings

120/240 Vac:

Make 30 amperes for 0.2 seconds, carry 7 amperes for 2 minutes, 3
amperes continuously, and break 5 amperes.

125/250 Vdc:

Make 30 amperes for 0.2 seconds, carry 7 amperes for 2 minutes, 3
amperes continuously, and break 0.3 ampere.

Inductive Ratings

120/240 Vac, 125/250 Vdc:

Make and carry 30 amperes for 0.2 seconds, carry 7 amperes for 2
minutes, 3 amperes continuously, and break 0.3 ampere. (L/R = 0.04).

Type Tests

Isolation

Meets IEC 255-5 and exceeds IEEE C37.90-1989 one-minute dielectric (high-potential) tests as follows.

All Circuits to Ground:

2,828 Vdc

Input to Output Circuits:

2,000 Vac or 2828 Vdc

Surge Withstand Capability

Qualified to IEEE C37.90.1-1989,

Standard Surge Withstand Capability (SWC) Tests for Protective

Relays and Relay Systems

Impulse

Qualified to IEC 255-5.

Summary of Contents for BE1-50/51B-229


























































Search results

Summary of Contents for BE1-50/51B-229

Reviews:

Related manuals for BE1-50/51B-229

Brands by name

Popular brands

Basler BE1-50/51B-229, Instruction Manual

Search results

Summary of Contents for BE1-50/51B-229

Reviews:

Related manuals for BE1-50/51B-229

Brands by name

Popular brands