Operation
7.
Connection
Plug the mains plug into a wall mains socket.
1.
Connect the product to a mixer or amplifier, if required. Ensure that all devices are turned off. Use a suitable
2.
cinch cable and connect it to the corresponding connector at the rear of the product as well as the mixer/
amplifier.
Playing back records
Switch the device on by turning the volume control in a clockwise direction.
1.
Remove the protective cap from the stylus.
2.
Put a record on the turntable. Place a single-adaptor (puck) on the turntable axis, if needed, to play single
3.
records.
Set the playback speed (33, 45 or 78) by using the speed control.
4.
Activate the autostop function, if required, using the autostop control.
5.
Position ON: At the end of the playback, the turntable will automatically stop turning.
-
Position OFF: At the end of the playback, the turntable will continue to turn.
-
Loosen the rest clip.
6.
Lift the pick-up arm by using the pick-up lift lever and move the pick-up toward the record. The turntable
7.
will be begin to rotate.
Lower the pick-up arm onto the record by using the pick-up lift lever. The playback of the record will begin.
8.
Now set the volume with the volume control.
9.
At the end of the playback, lift the pick-up arm by using the pick-up lift lever and move the pick-up arm
10.
back to the pick-up support.
Lower the pick-up arm by using the pick-up lift lever and secure the pick-up with the rest clip.
11.
Switch off the product by turning the volume control in an anticlockwise direction.
12.
Playing back cassettes
Switch the device on by turning the volume control in an clockwise direction.
1.
Insert an audio cassette into the cassette deck. The side with the tape has to face to the right side. The
2.
playback starts automatically.
Now set the volume with the volume control.
3.
To fast forward the cassette, carefully press the eject button until you hear a click sound. The button is now
4.
half-recessed in the housing and the cassette is being fast forwarded.
The playback or the fast forwarding will stopped automatically when the end of the current cassette side
5.
is reached.
To remove the cassette, press the eject button, which will then be completely recessed in the housing.
6.
Switch off the product by turning the volume control in an anticlockwise direction.
7.
Digitalising
8.
Connect the product to a computer via the USB cable.
1.
Insert the software CD and follow the on-screen instructions.
2.
You can find further information on the software functions in the help menu and in the operating instructions
3.
of the software. These are available at the following links:
http://audacity.sourceforge.net/help/documentation
http://lame.sourceforge.net/
Transport
9.
Disconnect all lines from the device and disconnect it from the power supply.
1.
Secure the pick-up arm with the rest clip.
2.
Put the protective plastic covering over the system needle.
3.
Pack the appliance back into its original packing.
4.
Cleaning
10.
The device should only be cleaned with a soft, dry cloth or brush from the outside.
•
Never use any aggressive cleaning agents or chemical solutions that may damage the surface of the
•
housing.
Make sure that the needle protection is in place while cleaning to avoid unnecessary damage to the pick-up
•
needle.
Disposal
11.
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
Technical data
12.
Operating voltage:
230 V/AC, 50 Hz
Power consumption:
12 W
Output power:
2 x 1.5 W RMS
System requirements:
Windows® 98 / ME / 2000 / XP / Vista™, Mac OS X 10.1 or later
Dimensions (W x H x D):
325 x 128 x 294 mm
Weight:
approx. 2.6 kg
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also
in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2011 by Conrad Electronic SE.
V1_0811_02-SB
