background image

 

 

 

- 29 - 

 

2. Safety instructions, standards, legal and regulatory 

provisions 

 

  Water supplying the water softening system must have the drinking water quality and 

comply with local regulations. 

  The maximum temperature of the supplied water may not exceed 40 °C.  

  Components of the water softening system that come into contact with water must be 

made of appropriate water-resistant material. 

  Make sure that a floor drain is available at the site of installation of the water 

softening system. 

  Do not disassemble the water softening system during its operation. 

  Do not open the water softening system, as this will void the guarantee. 

 
 
 

3. Intended use 

 

Safe operation of the device is only guaranteed when using the device for its intended 
purpose according to the instruction manual. 

The water softening device is designed for removing undesired mineral 
substances in the tap water (calcium and magnesium). 

The water softening device is part of the dishwasher protection system.

 

 

 CAUTION! 

Any use going beyond the intended purpose and/or any different use of the 
device is forbidden and is not considered as conventional. 

Any claims against the manufacturer or his authorized representative as a 
consequence of experiencing damages resulting from unconventional use 
are impossible. 

The operator is liable for all damages resulting from inappropriate use. 

Summary of Contents for WEH1350





























Reviews: