background image

BARTINGTON INSTRUMENTS

 

Page 3 of 11 OM2298/3

1. About this Manual

This document describes the installation, operation and maintenance of the Mag648 and Mag649 
magnetic field sensors.It should be read in conjunction with product brochure 

DS2298

 and 

outline drawings

 which can be found on the product page on the Bartington Instruments website 

at 

www.bartington.com

.

Note that failure to follow the instructions in this manual may invalidate your product’s warranty. 
If in doubt, do not hesitate to contact Bartington Instruments.

1.1. Symbols Glossary

The following symbols used within this manual call your attention to specific types of information:

WARNING: 

Indicates a situation in which serious bodily injury or death could result if the 

warning is ignored.

Caution: 

Indicates a situation in which bodily injury or damage to your instrument, or both, 

could result if the caution is ignored.

Identifies items that must be disposed of safely to prevent unnecessary damage to the 
environment.

Note: 

A note provides useful supporting information and sometimes suggests how to make 

better use of your purchase.

2. Safe Use

WARNING:

 These products are not qualified for use in explosive atmospheres or life 

support systems. Consult Bartington Instruments for advice.

Caution: 

To prevent irreparable damage, electrostatic discharge (ESD) protection and 

precautions must be used when handling the unpackaged sensor electronics board.

3. Introduction to the Mag648 & Mag649 Series

Both the Mag648 and Mag649 are magnetometers consisting of a cluster of three, feedback 
stabilised, fluxgate sensors arranged along X, Y and Z axes. Each axis provides a highly 
linear magnetic response, with low hysteresis and low crosstalk between axes. These 
characteristics, combined with the compact design and very low power consumption, make 
these magnetometers ideally suited for perimeter surveillance with a multi-sensor network. 
Regulating the power supply internally ensures the Mag64x series is suitable for battery powered 
operation, over both long and short cables.

Summary of Contents for Mag648












Reviews: