Barrett 1101 Installation And Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 15

background image

#0-313A-SBA (6/01)
Page 15 of 14 pages
BARRETT CENTRIFUGALS INC.
1-800-228-6442

Check that when the lever is in the closed position the lever site hole is aligned properly with
the sensor tip and solenoid pin. If not, adjust the latch stop position by turning the stop
adjusting screw.

Be sure to replace and securely fasten the sheet metal guard and enclosure cover
when complete.

BEARINGS

The bearings in this machine are for centrifugal application having special internal fits and
should be purchased from Barrett.

REPAIR PARTS

Repair parts are available from:

Barrett Centrifugals Inc.

156 Goddard Memorial Drive

Worcester, MA 01603

Telephone: 800-228-6442 or 508-754-6891

Fax: 508-756-5342

E-mail:

[email protected]

Web Site: Barrettinc.com

Be sure to specify the serial number of the machine, found either on the control panel
nameplate and / or stamped on the machine base, when ordering parts.

«
...
13
14
15

Summary of Contents for 1101
















Reviews:

No comments

Related manuals for 1101

Brand: Eagle power Pages: 13

Hydro-Force MX3-200H

Brand: Nautilus Pages: 55

Brand: Ice Pages: 56

Brand: Ice Pages: 78

Brand: GADLEE Pages: 2

Brand: Kärcher Pages: 392

Brand: Minuteman Pages: 84

Brand: Abicor Binzel Pages: 100

Brand: Wascomat Pages: 32

Brand: FAST CLEAN Pages: 9

Brand: Kärcher Pages: 240

Brand: Lavor Pages: 180

Brand: YANGZI Pages: 13

Saber Cutter series

Brand: Windsor Pages: 3

Brand: Windsor Pages: 25

Chariot 3 iScrub 26

Brand: Windsor Pages: 3

Saber Compact 10052190

Brand: Windsor Pages: 29

Saber Compact 10052150

Brand: Windsor Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands