background image

16

Barnstead|Thermolyne Corporation warrants that if a product manufactured by

Barnstead|Thermolyne and sold by it within the continental United States or Canada
proves to be defective in material or construction, it will provide you, without charge, for a
period of ninety (90) days, the labor, and a period of one (1) year, the parts, necessary to
remedy any such defect. Outside the continental United States and Canada, the warranty
provides, for one (1) year, the parts necessary to remedy any such defect. The warranty
period shall commence either six (6) months following the date the product is sold by
Barnstead|Thermolyne or on the date it is purchased by the original retail consumer,
whichever date occurs first.

All warranty inspections and repairs must be performed by and parts obtained from

an authorized Barnstead|Thermolyne dealer or Barnstead|Thermolyne (at its own
discretion). Heating elements, however, because of their susceptibility to overheating and
contamination, must be returned to our factory, and if, upon inspection, it is concluded that
failure is not due to excessive high temperature or contamination, warranty replacement will
be provided by Barnstead|Thermolyne. The name of the authorized
Barnstead|Thermolyne dealer nearest you may be obtained by calling 1-800-446-6060 or
writing to:

Barnstead|Thermolyne

P.O. Box 797

2555 Kerper Boulevard

Dubuque, IA 52004-0797

USA

FAX: (319) 589-0516

E-MAIL ADDRESS: [email protected]

Barnstead|Thermolyne’s sole obligation with respect to its product shall be to repair

or (at its own discretion) replace the product. Under no circumstances shall it be liable for
incidental or consequential damage.

THE WARRANTY STATED HEREIN IS THE SOLE WARRANTY APPLICABLE TO

Barnstead|Thermolyne PRODUCTS. Barnstead|Thermolyne EXPRESSLY DISCLAIMS
ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR USE.

One Year Limited Warranty

9001

ISO

REGISTERED

Barnstead|Thermolyne

2555 Kerper Blvd.
P.O. Box 797
Dubuque, IA  52004-2241
Phone: 319-556-2241  800-553-0039
Fax: 319-589-0516
E-Mail Address: [email protected]

Summary of Contents for 494 Series

















Reviews: