Barnes 10CCE, Installation And Operation Manual

Page: 4 / 22

4
DISCHARGE ..................
1½” (38mm) x 1½ (38mm) NPT ,
Female
LIQUID TEMPERATURE
160°F (71°C) Continuous
INTERMEDIATE .............
Cast Iron ASTM A-48, Class 30
VOLUTE .........................
Cast Iron ASTM A-48, Class 30
BODY .............................
Cast Iron ASTM A-48, Class 30
PEDESTAL .....................
Cast Iron ASTM A-48, Class 30
IMPELLER Design ...........
Semi-Open
Material ........
Cast Iron ASTM A-48, Class 30
Dynamically Balanced, ISO G6.3
SHAFT ............................
Stainless Steel
SQUARE RINGS ............
Buna-N
HARDWARE ..................
300 Series Stainless Steel
PAINT .............................
Air dry enamel
SEAL Design ..........
Mechanical
Lubrication....
Self-Lubrication
Material ........
Rotating Faces - Carbon
Stationary Faces - Ceramic
Elastomer - Buna-N
Hardware - 300 series stainless steel
CHECK VALVE:
Material ........
Valve Flap - Neoprene
Weight - Cast Iron ASTM A-48, Class 30
MOTOR: Design ..........
ODP, NEMA L, Single phase,
NEMA B, Three Phase Torque Curve,
C-Face, Footed, Squirrel Cage
Induction
Insulation ......
Class B
SINGLE PHASE .............
Dual Voltage 115/230, capacitor
start
THREE PHASE ..............
200-240/480 is Tri voltage motor.
OPTIONAL EQUIPMENT:
Seal Material, TEFC motors
SECTION: A - PUMP SPECIFICATIONS: 3CCE, 4CCE, 5CCE
inches
(mm)
MODEL
NO.
HP VOLTS PH RPM
(Nom)
ODP MOTOR DESIGN TEFC MOTOR DESIGN
* A
DIM FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
WEIGHT
NET LBS
* A
DIM FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
3CCE 1.5 200-230/460 3 3450 17.88 (454) 6.0/3.0 40/20 84 20.00 (508) 5-4.6/2.3 36/18
3CCE-1 1.5 115/230 1 3450 18.44 (468) 4.5/2.3 12/60 84 21.00 (534) 16.6/8.3 84/42
4CCE 2.0 200-230/460 3 3450 18.44 (468) 6.8/3.4 50/25 92 21.00 (534) 7-5.4/2.7 46/23
4CCE-1 2.0 115/230 1 3450 18.44 (468) 5.9/3.0 144/72 92 21.92 (557) 23/11.5 156/78
5CCE 3.0 200-230/460 3 3450 18.44 (468) 9.6/4.8 64/32 94 21.92 (557) 8.1-7.6/3.8 66/33
5CCE-1 3.0 115/230 1 3450 19.69 (500) 8.3/4.2 204/102 94 25.36 (644) 29/14.5 172/86
IMPORTANT!
1.)
DO NOT
USE FOR PUMPING FLUIDS WITH A FLASH POINT OF LESS THAN 100°F.
2.) MAKE CERTAIN THAT PUMP AND/OR MOTOR ASSEMBLY AND CONTROLS HAVE THE APPROPRIATE RATINGS FOR THE GIVEN
APPLICATION AREA CLASSIFICATION (ie DIVISION I, AGENCY LISTING ETC.)
“A” - Overall Dimensions subject to Motor Manufacture