background image

1.3 Safety

WARNING

Ÿ

The operator must be aware of safety precautions to prevent physical injury.

Ÿ

Any pressure-containing device can explode, rupture or discharge its contents if it is over-pressurized. 
Take all necessary measures to avoid over-pressurization.

Ÿ

Operating, installing or maintaining the unit in any way that is not covered in this manual could cause 
death, serious personal injury, or damage to the equipment. This includes any modification to the 
equipment  or  use  of  parts  not  provided  by  the  manufacturer.  If  there  is  a  question  regarding  the 
intended use of the equipment, please contact a BARMESA representative before proceeding.

Ÿ

This  manual  clearly  identifies  accepted  methods  for  disassembling  units. These  methods  must  be 
adhered to. Trapped liquid can rapidly expand and result in a violent explosion and injury. Never apply 
heat to impellers, propellers or their retaining devices to aid in their removal.

Ÿ

Do not change the service application without the approval of an authorized BARMESA representative.

CAUTION

You must observe the instructions contained in this manual. Failure to do so could result in physical injury, 
damage, or delays.

1.4 User safety

General safety rules

Ÿ

Always keep the work area clean.

Ÿ

Pay attention to the risks presented by gas and vapors in the work area.

Ÿ

Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash hazards.

Ÿ

Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

NOTICE

Never operate a unit unless safety devices are installed. Also see specific information about safety devices 
in other chapters of this manual.

Electrical connections

These must be made by certified electricians in compliance with all intemational, national, state, and local regulations. 
For more information about requirements, see sections dealing specifically with electrical connections.

1.5 Enviromental safety

The work area

Always keep the station clean to avoid and/or discover emissions.

barmesa.com

6

Summary of Contents for 2KLEIN-051




















Reviews: