background image

Manual 2100-737A 

Page 

2 of 25

Figures

Figure 1  Fresh Air Damper .................................. 5 

Figure 2  Unit Dimensions ................................... 7

Figure 3  Mounting Instructions............................ 8

Figure 4  Electric Heat Clearance ......................... 9

Figure 5  Wall Mounting Instructions .................. 10

Figure 6  Wall Mounting Instructions .................. 10

Figure 7  Common Wall Mounting Installations .... 11

Figure 8  Compressor Cutoff Thermostat Wiring .... 13

Figure 9  Compressor Cutoff Thermostat Wiring .... 13

Figure 10 Electric Heat Hold-Off Wiring ............... 14

Figure 11 Electric Heat Hold-Off Wiring ............... 14

Figure 12 Defrost Control Board .......................... 17

Figure 13 Fan Blade Setting ............................... 21

Figure 14 Control Disassembly ............................ 28

Figure 15 Winding Test ....................................... 28

Figure 16 Drip Loop ........................................... 28

Tables

Table 1  Troubleshooting .................................. 19

Table 

Temperature F vs. Resistance ............... 20

Table 2  Fan Blade Dimension .......................... 21

Table 3A  Cooling Pressures ................................ 22

Table 3B  Heating Pressures ............................... 22

Table 4  Electrical Specifications ...................... 22

Table 5  Indoor Blower Performance .................. 23

Getting Other Information and Publications .... 3

W

all Mount General Information ......................... 4

Heat Pump Wall Mount Model Nomenclature .......... 4

Shipping Damage ................................................. 4

General ............................................................... 4

Duct Work  ........................................................... 5

Filters ................................................................. 5

Fresh Air Intake ................................................... 5

Condensate Drain  ................................................ 5

I

nstallation Instructions ........................................ 6

Wall Mounting Information .................................... 6

Mounting the Unit ................................................ 6

Placement  ........................................................... 6

Clearances Required ............................................. 6

Minimum Clearances ............................................ 6

Wiring – Main Power ........................................... 12

Wiring – Low Voltage Wiring ................................. 12

Optional Outdoor Thermostat Applications ............ 13

Optional Compressor Cutoff Thermostat ................ 13

Electric Heat Hold-Off ........................................ 14

Start Up ................................................................... 15

General   ......................................................... 15

Topping Off System Charge ................................. 15

Safety Practices ................................................. 15

Important Installer Note ...................................... 16

High and Low Pressure Switch ............................. 16

Three Phase Scroll Compressor Start Up  

Information ........................................................ 16

Phase Monitor .................................................... 16

Service Hints ..................................................... 16

Sequence of Operation ........................................ 16

 Cooling .......................................................... 16

 Heating ......................................................... 16

Pressure Service Ports ........................................ 17

Defrost Cycle ..................................................... 17

  Low Pressure Bypass Operation ........................ 18

  High Pressure Switch Operation ....................... 18

Service ..................................................................... 19

Solid State Heat Pump Control Troubleshooting

Procedure  ......................................................... 19

Checking Temperature Sensor Outside Unit Circuit ...20

Fan Blade Setting Dimensions ............................. 21

Removal of Fan Shroud ....................................... 21

R-410A Refrigerant Charge ................................. 21

Troubleshooting GE ECM Motors .......................... 24

CONTENTS

Summary of Contents for T60H2-A


























Reviews: