![background image](http://html.mh-extra.com/html/barco/xdx/xdx_installation-manual_474403024.webp)
R5914481 /02 XDX
24
3.1 Installation requirements
Environmental conditions
The table below summarizes the physical environment in which the XDX series projector can be operated or
stored.
Environment
Operating
Non-Operating
Ambient Temperature
10°C (50°F) to 40°C (104°F)
-15°C (5°F) to 60°C (140°F)
Air cleanliness
Clean office environment (equivalent with
clean room standard ISO 14644-1 ISO Class
9)
n.a.
Humidity
5% RH to 85% RH Non-Condensed
5% to 95% RH Non-Condensed
Altitude
-60 (-197 ft) to 4.000 m (13.125 ft)
1
-60 (-197 ft) to 10.000 m (32.810
ft)
Let the projector acclimatize after unpacking. Neglecting this may result in a failure in the start-up of
the Light Processor Unit.
Use in high altitude conditions
Combining high altitude and high ambient temperature creates extra challenging conditions for any electronics
system; projectors are no exception to this. The system can be used up to 4.000 m (13.125 ft) altitude
, but the
maximum ambient temperature should be reduced once exceeding 2.500 m (8.202 ft). This in accordance
with the following table:
Altitude (m)
Altitude (ft)
Temp (°C)
Temp (°F)
0
0
40
104
2 000
6 562
40
104
2 500
8 202
39
102
3 000
9 842
38
100
3 500
11 483
37
99
4 000
13 123
35
97
Main Power requirements
Depending on the available power circuit, all XDX projectors can operate from a single-phase power net or
three-phase power net.
Power system
Power requirements
three-phase power net
•
200–240V/346–415V, 3W+N+PE, 15A, 50/60 Hz (Y)
•
200–240V, 3W+PE, 20A, 50/60 Hz (Δ)
single-phase power net
200–240 VAC, L1+L2/N+PE, 25A, 50/60 Hz
The projector must be switched internally between a star connection (Y), a delta connection (Δ) or a mono-
phase connection or vice versa. See
“Connecting the projector with the power net”, page 44
The power cord required to connect the projector with the power net is not delivered with the projector. It is the
responsibility of the customer to provide the correct type of power cord. The cross-sectional area of the
conductors in the power supply cord shall not be less than 4 mm
2
(10 AWG).
In single-phase operation, the power cord must be rated for
minimum 300 V
.
1.
Limited to 2.000 meters (6.562 feet) for Chinese Mainland due to local regulations.
Summary of Contents for XDX
