![background image](http://html1.mh-extra.com/html/barco/xdl/xdl_installation-manual_4060127013.webp)
13
R5906150 /05
XDL
•
Disconnect the power to the projectors mains terminals before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine or
abrasive cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth
lightly dampened with mild detergent solution.
•
To ensure the highest optical performance and resolution, the projection lenses are specially treated with
an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry
cloth. For lens cleaning follow the instructions precisely as stipulated in the projector manual.
•
Rated maximum ambient temperature, t
a
= 35 °C (95 °F).
•
Rated humidity = 5% RH to 80% RH Non-condensed.
•
An external frame must be used to stack projectors.
•
For functionality and reliability, the projector requires accurate temperature control and cooling below
ambient. Therefore a liquid cooling system is provided consisting of liquid circuits inside the projector
which are connected via hoses to external chillers. Only chiller models and hoses exclusively developed
for this application and approved by Barco are allowed to be used. Barco approved chillers models are
listed on the Barco website.
•
An adequate draining system must be coupled with the drain pipes at the bottom of the projector to collect
and lead away the condensed water from the built-in air-dryers. The capacity of the draining system must
meet the humidity conditions wherein the projector operates. The water drain must arrives into an 'open'
water container!
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage potentials and risk of electric shock.
•
Refer all servicing to qualified service personnel.
•
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the projector and cancellation of the warranty.
•
Remove all power from the projector and refer servicing to qualified service technicians under the following
conditions:
-
When the power cord or plug is damaged or frayed.
-
If liquid has been spilled into the equipment.
-
If the product has been exposed to rain or water.
-
If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
-
If the product has been dropped or the cabinet has been damaged.
-
If the product exhibits a distinct change in performance, indicating a need for service.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts which have the same characteristics as the
Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire,
electric shock or other hazards. Unauthorized substitutions may void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available
upon request via [email protected].
Summary of Contents for XDL
