![background image](http://html.mh-extra.com/html/barco/xdl-series/xdl-series_installation-manual_474397110.webp)
R5906150 /02
XDL
110
Stage 6 :
Projector is
CONDITIONED
and
ON
. Temperature and humidity inside the sealed compartments are
within specifications and the lasers are activated. The backlight of the On/Off button is blue. Once you press
the Shutter button (reference C, Image 10-4), the image will be projected on the screen (if a source has been
selected or a test pattern is active). The laser status light on the top of the projector lights up white.
While the shutter is closed (backlight of Shutter button is red) the laser power is set to minimum
power and a protective test pattern is projected. This to protect the DMDs and Shutter itself. When
you open the shutter again, the projector will resume the previous power settings.
Stage 7 :
Projector is in
DECONDITIONING
mode. This process starts as soon as the On/Off button is
pressed for 3 seconds (reference D, Image 10-4) while the projector is in conditioning or conditioned mode.
The DECONDITIONING mode brings the system back to the
READY
mode. The laser status light on the top
of the projector remains lighting up white. The sealed compartments are brought back to ambient temperature
and humidity extraction is stopped. The deconditioning process can take up to 15 minutes (depending on the
environmental conditions). During this process the backlight of the Power On/Off button is blinking white.
If the projector is left alone for several minutes while it is in
READY
mode, the projector will automatically go
into
STANDBY
mode. You can also go from Ready to Standby mode by pushing the On/Off button for 3
seconds.
Stage 8 :
Projector is in
STANDBY
mode. The Input & Communication Unit remains running, but only the On/
Off button is active and solid white. The shutter button turns off. The laser status light remains off.
By pressing the On/Off button, you activate the projector and go to
CONDITIONING
mode (effectively skipping
Ready mode). Alternatively, you can transition to
READY
mode instead. Do this by pressing the (non-lit) Menu
button for three seconds.
10.4 Using the RCU
Pointing to the reflective screen
1.
Point the front of the RCU to the reflective screen surface.
Image 10-5: IR control via reflective screen
Hardwired to the XLR input
1.
Plug one end of the remote cable in the connector on the bottom of the RCU.
2.
Plug the other end in the big connector on the communication interface of the projector, labelled
‘
Remote
CTRL
’
.
Note:
Plugging the remote control will switch the broadcast address of the remote control to the
default value '0'. This is the only broadcast address that will work when hardwired. If you want to
change the broadcast address after disconnecting the remote control, see
Programming addresses into the RCU
”
, page 47.
Summary of Contents for XDL Series
