![background image](http://html1.mh-extra.com/html/barco/iq-pro-r500/iq-pro-r500_owners-manual_474185185.webp)
18. SNMP services
18. SNMP SERVICES
Introduction
Some parameters values are installation dependent, and are shown here as an example.
You may need assistance from you network administrator, IT Manager or MIS helpdesk to obtain the settings or to configure
the projector for you, since this is a task description targeted to ‘Administrators’ and needs knowledge and/or permissions
normally held by those persons.
It is advised that you first try to follow the procedure to obtain a working setup, before changing the settings for conforming to your
local security requirements.
18.1 SNMP installation
Introduction
The Control Server version should be at least version 1.10.
To check the version, open the about box from the server tray:
Software updates can be obtained from the BARCO support website: ftp://ftp.barco.com/pub/iq_pro_software/
or from secured website PartnerZone
How to install SNMP (only if necessary)
1. The Microsoft SNMP service must be installed
You may need to install this service from the Windows XP CDROM.
2. Install the SNMP Agent Extension dll
regsvr32 IQProSNMP.dll
The agent should now be registered as “iqpro” under
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters\ExtensionAgents
How to configure SNMP (only if necessary)
1. Go to the Control panel, under the Administrative Tools, in the Services, in the “SNMP” entry.
2. In the “General” tab, you can enable the service, and make it start automatically.
3. In the “Security” tab, the default Community is called ‘public’ and is read-only.
You may want to give read-write permission to ‘public’ (not recommended) or create a ‘private’ community
with read-write permissions.
4. In the Control Server, enable the SNMP support, and optionally, enable read-write support.
5. The SNMP service should be restarted, to take the changed settings into account.
To uninstall the snmp agent: regsvr32 /u IQProSNMP.dll
18.2 SNMP integration
Commands
Following commands are provided stored in the MIB :
Command
Type
PROJECTORTYPE
READ
SERIALNUMBER
READ
R5976694 IQ PRO R500 01/02/2007
179
Summary of Contents for iQ Pro R500
