8. Input
DVI/HDMI/DP
5–cable analog
DVI analog
SDI
Fpix
≤
210 MHz
Fpix
≤
210 MHz
Fpix
≤
170 MHz
Fpix
≤
150 MHz
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
Side-by-Side
Interlaced/progressive
Interlaced/progressive
Interlaced/progressive
Interlaced/progressive
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
Max. resolution:
1920x1200@60Hz or
2048x1080@60Hz.
Top-and-Bottom
Progressive only
Progressive only
Progressive only
Progressive only
2xDVI/2xHDMI/2xDP
1
2xSDI
2
Fpix
≤
210MHz.
Fpix
≤
150MHz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
Max. resolution:
1920x1200@30Hz, 2048x1080@30Hz
or 1280x720@60Hz.
Frame Sequential
Dual Channel
Progressive only
Progressive only
SDI (3G - Level B)
3
Fpix
≤
150MHz.
Line Alternating (3G-B)
Max. resolution
1920x1200@30Hz, 2048x1080@30Hz or 1280x720@60Hz.
HDMI/DP
Fpix
≤
162MHz & Vfreq
≤
60Hz.
Max. resolution:
1920x1200@60Hz or 2048x1080@60Hz.
SENSIO
®
3D Decoder - FFC
Progressive only
Other settings to use the 3D glasses
Adjust the following setting:
•
Dark time
•
L/R output reference delay
•
3D Sync Loop Through
These settings can be found as follows:
MENU
>
Alignment
>
3D Glasses
8.9.2
Activate 3D
What can be done ?
The status of the 3D function can be enabled or disabled.
This function is input dependent.
How to enable/disable
Press
Menu
to activate the menus and select
Input
→
3D
→
Status
.
1. 2x HDMI and 2x DP requires 2 3D input modules. 2xDVI can be done with a DVI input and a 3D input with DVI to HDMI convertor
2. For 2xSDI, IN1 and IN2 of the SDI input can be used. The input settings under MENU -> Input -> Advanced Settings -> SDI/HDSDI/3G must be set to ‘DUAL SDI’
3. For SDI (3G- Level B), IN1 or IN2 of the SDI input can be used. The input settings under MENU -> Input -> Advanced Settings -> SDI/HDSDI/3G must be set to ‘Input 1’ or ‘Input 2’,
with or without Priority
R5905158 HDF SERIES 16/06/2015
91
Summary of Contents for HDF W series
