Barco F35, Reference Manual

Page: 13 / 24

MFBX Factory Measured Blue X GP3, GP4
Get, Set
Manufacturing
MFBY
Factory Measured Blue Y GP3, GP4
Get, Set
Manufacturing
MFBL Factory Measured Blue
Luminance GP3, GP4 Get, Set Manufacturing
MFWX
Factory Measured White X GP3, GP4
Get, Set
Manufacturing
MFWY Factory Measured White Y GP3, GP4 Get, Set Manufacturing
MFWL
Factory Measured White
Luminance GP3, GP4
Get, Set
Manufacturing
MFDX Factory Measured BC1 X GP3 Get, Set Manufacturing
MFDY
Factory Measured BC1 Y GP3
Get, Set
Manufacturing
MFDL Factory Measured BC1
Luminance GP3 Get, Set Manufacturing
MFEX
Factory Measured BC2 X GP3
Get, Set
Manufacturing
MFEY Factory Measured BC2 Y GP3 Get, Set Manufacturing
MFEL
Factory Measured BC2
Luminance GP3
Get, Set
Manufacturing
CMTP Color Management Test Patterns GP3, GP4 Get, Set End User
IBCO
Individual brightness and contrast
offset adjustments GP3, GP4
Get, Set
End User 0 - disable, 1 - enable 0-RGB, 1-IR
(if available)
BOR0 Brightness offset red GP3, GP4 Get, Set End User
BOG0
Brightness offset green GP3, GP4
Get, Set
End User
BOB0 Brightness offset blue GP3, GP4 Get, Set End User
COR0
Contrast offset red GP3, GP4
Get, Set
End User
COG0 Contrast offset green GP3, GP4 Get, Set End User
COB0
Contrast offset blue GP3, GP4
Get, Set
End User
DESK Select orientation - Desktop Front GP3, GP4 Get, Set End User
CEIL
Select orientation - Ceiling Front GP3, GP4
Get, Set
End User
RDES Select orientation - Desktop Rear GP3, GP4 Get, Set End User
RCEI
Select orientation - Ceiling Rear GP3, GP4
Get, Set
End User
ORIE Select orientation - Absolute
value GP3, GP4 Get, Set End User See value table ORIE
SCAN
Source Scan GP3, GP4
Get, Set
End User 0 - disable, 1 - enable
IR01 IR Enable 1 GP3, GP4 Get, Set End User 0 - disable, 1 - enable
IR02
IR Enable 2 GP3, GP4
Get, Set
End User 0 - disable, 1 - enable
IR03 IR Enable 3 GP3 Get, Set End User 0 - disable, 1 - enable
OSDC
OSD Enable GP3, GP4
Get, Set
End User See value table OSDC
TEST Test Image GP3, GP4 Get, Set End User 0 - 7 different test patterns
DHED
Dual Head Setup Mode GP3, GP4
Get, Set
End User 0 - off, 1 - side by side
SVGA Sync termination VGA GP3, GP4 Get, Set End User 0 - 2.2kOhm, 1 - 75Ohm
SNCL
Sync level VGA GP3, GP4
Get, Set
End User 0-255
SNCS Sync Level SOG GP3, GP4 Get, Set End User 0-31 Infitec only
OPFI
Infitec filter GP3
Get, Set
End User 0 - disable, 1 - enable Infitec only
CSCC Infitec CSC GP3 Get, Set End User 0 - disable, 1 - enable
EDIR
Edit resolution GP3, GP4
Get, Set
End User See value table EDIR
EDIT Edid type GP3, GP4 Get, Set End User See value table EDIT
Installation
Picture->Advanced->Source Correction
3. ASCII Command Sets
601-0381-00_GP3/GP4
Sicilium_1_24
10
All manuals and user guides at all-guides.com