![background image](http://html1.mh-extra.com/html/barco/clm-hd8/clm-hd8_user-manual_473954049.webp)
6. Getting started
Ind.
Key name
Description
14
PHASE
Used to remove the horizontal instability of the image (usually for RGB source). It adjusts
the phase of the pixel sampling clock relative to the incoming signal.
15
FREEZ
To freeze the actual projected image. Freeze sign is displayed in the upper left corner (a
short press on the key).
When pressing for 5 sec, the projector goes into stand-by. The lamp cooling fans remain
active for about 5 minutes. The speed of the other fans is reduced.
16
TEXT
Toggle key to activate or deactivate on screen text boxes while adjusting a setting.
When adjusting one of the image controls, e.g.during a meeting, the normally displayed
bar scale can be deactivated by pressing ’TEXT’ key
fi
rst. To re-display the bar scale
on the screen, press ’TEXT’ key again. When TEXT is ’off’, no adjustment menu’s
will be displayed on the screen when entering the adjustment mode. All menus and
adjustments remain active on the local LCD panel.
17
ENTER
Key to con
fi
rm an adjustment or selection in the adjustment mode.
18
Cursor keys
To make menu selections when in the adjustment mode
19
EXIT
Key to go one menu stage higher than the actual position when in the adjustment mode.
20
WINDOW
Selection of the active window, also in PIP mode.
21
PIP
Direct access key for picture in picture selection.
22
RC Operating indication
Lights up when a button on the remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
Table 6-1
6.3
Operating the projector
Overview
•
•
Errors, warnings and messages during start up
•
•
All four lamps must be physically installed before operating the projector.
6.3.1
Switching on
How to switch on.
1. Press the power switch to switch on the projector.
Image 6-2
Power switch
-
When ’0’ is visible, the projector is switched off.
-
When ’1’ is visible, the projector is switched on.
The projector starts up in standby. The menus are accessible via the local LCD panel.
To display an image, the standby key must be pressed once.
R59770057 CLM HD8 15/03/2010
45
Summary of Contents for CLM HD8
