Barco BarcoVision R9000740701, Owner'S Manual

Page: 137 / 161

R5975238 BARCOVISION 701 MULTIMEDIA 070497
APPENDIX B : ORBITING
AP
P
E
NDI
X
B
: O
RBI
TI
NG
R5975238 BARCOVISION 701 MULTIMEDIA 070497
APPENDIX B : ORBITING
AP
P
E
NDI
X
B
: O
RBI
TI
NG
B-3 B-3
Orbiting speed toggle (only in MASTER Orbiting)
Highlight 'SPEED : SLOW' with
the coontrol disk and press EN-
TER to set the ORBITING SPEED
to Fast.
Highlight 'SPEED : FAST' with the
control disk and press ENTER to
set the ORBITING SPEED to Slow
ENTER continues to Set up Orbiting.
EXIT returns to the Path Selection menu.
ADJUST returns to the Operational mode.
Orbiting alignment
Preparation :
Before proceeding to the alignment of the Orbiting default settings, be sure that
the Horizontal Phase and the Raster shift are correctly aligned with the Orbiting
mode set to OFF.
This alignment must be performed in case of a multiple projector installation with
Master and Slave projectors in order to ensure a correct operation of the Orbiting
for all projectors.
Adjustment procedure stand alone projector :
Highlight 'ADJUST DEVIATION'
with the control disk and press
ENTER.
M A S T E R O R B I T I N G
< EX IT > t o r et ur n
S EL E CT WI T H O R
T H E N < E N T E R >
D E VI A T I O N A D J U ST :
V ER TI CA L W IT H OR
H OR I Z ON T A L W I TH O R
C H A N G E T O S L A V E
M O D E : O N
S P E E D: F A S T
A D J U S T DE V I A T I O N
M A S T E R O R B I T I N G
< EX IT > to r et ur n
S EL E CT WI T H O R
T H E N < E N T E R >
D E VI A T I O N A D J U ST :
V ER TI CA L W IT H OR
H OR I Z ON T A L W I TH O R
C H A N G E T O S L A V E
M O D E : O N
S P E E D: F A S T
A D J U S T DE V I A T I O N
Orbiting speed toggle (only in MASTER Orbiting)
Highlight 'SPEED : SLOW' with
the coontrol disk and press EN-
TER to set the ORBITING SPEED
to Fast.
Highlight 'SPEED : FAST' with the
control disk and press ENTER to
set the ORBITING SPEED to Slow
ENTER continues to Set up Orbiting.
EXIT returns to the Path Selection menu.
ADJUST returns to the Operational mode.
Orbiting alignment
Preparation :
Before proceeding to the alignment of the Orbiting default settings, be sure that
the Horizontal Phase and the Raster shift are correctly aligned with the Orbiting
mode set to OFF.
This alignment must be performed in case of a multiple projector installation with
Master and Slave projectors in order to ensure a correct operation of the Orbiting
for all projectors.
Adjustment procedure stand alone projector :
Highlight 'ADJUST DEVIATION'
with the control disk and press
ENTER.
M A S T E R O R B I T I N G
< EX IT > to r et ur n
S EL E CT WI T H O R
T H E N < E N T E R >
D E VI A T I O N A D J U ST :
V ER TI CA L W IT H OR
H OR I Z ON T A L W I TH O R
C H A N G E T O S L A V E
M O D E : O N
S P E E D : F A S T
A D J U S T D E V I A T I O N
M A S T E R O R B I T I N G
< EX IT > t o r et ur n
S EL E CT WI T H O R
T H E N < E N T E R >
D E VI A T I O N A D J U ST :
V ER TI CA L W IT H OR
H OR I Z ON T A L W I TH O R
C H A N G E T O S L A V E
M O D E : O N
S P E E D : F A S T
A D J U S T D E V I A T I O N