Barco BarcoVision R9000740701, Owner'S Manual

Page: 107 / 161

R5975228 BARCOVISION 701 MULTIMEDIA 070597
SERVICE MODE
SER
VI
C
E
M
O
D
E
R5975228 BARCOVISION 701 MULTIMEDIA 070597
SERVICE MODE
SER
VI
C
E
M
O
D
E
9-5
9-5
V 701 MULTIM EDI A
P ro j . a d dr e s s : 00 1
S of t . V er si on : 5 . 0 0
C on f ig . : C ei l in g
front
B a u d r a t e P C : 9 6 0 0
T e x t : O N
S e r i al N o . : 1 03 5 9 8 5 2
The 'Identification' screen gives in-
formation concerning :
- Projector address. To change the
address of your projector, contact
a qualified service technician.
- Software version.
- Configuration.
Possible installations :
* Front-ceiling
* Front-table
* Rear-ceiling
* Rear-table
- Baud rate PC : transfer speed for communication with an IBM PC (or compat-
ible) or MAC. The baud rate of the projector must be the same as the baud rate
of the connected computer. When there is a difference, contact a qualified
service technician to make the appropriate changes.
- Text ON/OFF
Indicates in operational mode if the bar scale and number indicator will be
displayed and if warnings and failures will be displayed.
ON : displayed
OFF : not displayed
The status can be changed by pressing the 'TEXT' key once on the RCU.
- Serial no. : indicates the fabrication number of the projector. This number can
be useful when calling for technical assistance.
Total Run Time
Select with or
then <ENTER>
<EXIT> to return.
PROJECTOR SET-UP
Highlight 'Total Run Time' with the
control disk and press ENTER to
display the amount of time the pro-
jector has played since its first start
up at the factory.
ENTER gives the selected item.
EXIT returns to the Service mode menu.
ADJUST returns to the Operational mode.
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
V 701 MULTIM EDI A
P ro j . a d dr e s s : 00 1
S of t . V er si on : 5 . 0 0
C on f ig . : C ei l in g
front
B a u d r a t e P C : 9 6 0 0
T e x t : O N
S e r i al N o . : 1 03 5 9 8 5 2
The 'Identification' screen gives in-
formation concerning :
- Projector address. To change the
address of your projector, contact
a qualified service technician.
- Software version.
- Configuration.
Possible installations :
* Front-ceiling
* Front-table
* Rear-ceiling
* Rear-table
- Baud rate PC : transfer speed for communication with an IBM PC (or compat-
ible) or MAC. The baud rate of the projector must be the same as the baud rate
of the connected computer. When there is a difference, contact a qualified
service technician to make the appropriate changes.
- Text ON/OFF
Indicates in operational mode if the bar scale and number indicator will be
displayed and if warnings and failures will be displayed.
ON : displayed
OFF : not displayed
The status can be changed by pressing the 'TEXT' key once on the RCU.
- Serial no. : indicates the fabrication number of the projector. This number can
be useful when calling for technical assistance.
Total Run Time
Select with or
then <ENTER>
<EXIT> to return.
PROJECTOR SET-UP
Highlight 'Total Run Time' with the
control disk and press ENTER to
display the amount of time the pro-
jector has played since its first start
up at the factory.
ENTER gives the selected item.
EXIT returns to the Service mode menu.
ADJUST returns to the Operational mode.
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO