5975617 BARCOVISION 8100 150197
CONNECTIONS
CO
NN
E
C
T
IO
N
S
5975036 BARCOVISION 8100 150197
CONNECTIONS
7-14
7-14
CO
NN
E
C
T
IO
N
S
Set up of the baud rate for communication with a computer.
The communication speed between projector and computer, e.g. PC or MAC, has 8
possible speeds. With DIP switches S2(1,2,3) on the controller unit, it is possible to
select the baud rate (communication speed).
Gaining access to the DIP switches
Power down the projector and unplug the power cord from the wall outlet.
Turn both lock screws with a screwdriver or coin counter clockwise.
Lift up and pivot the top cover. Attention : the cover is not secured with an
incorporated support. When opening, turn it over slowly and lay it down on the
second part of the top cover.
The processor module with the DIP switches is located on top, the front left side
(seen from the front of the projector, see next page).
Loosen the locking
screws.
Open the top cover
R
B
V
R
B
V
100 - 230 V
9 - 4 A
60 - 50 Hz
RS232 OUT
0
I
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) This device may not cause harmful interference
(2) This device must accept any interference received
including interference that may cause undesired operation
I R- A CK NO WL E DG E D
I R- RECE I V E D
DIA GNO STICS
CO DE
I R- RECE I V E R
R
B
V
R
B
V
100 - 230 V
9 - 4 A
60 - 50 Hz
RS232 OUT
0
I
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) This device may not cause harmful interference
(2) This device must accept any interference received
including interference that may cause undesired operation
I R- A CK NO WL E DG E D
I R- RECE I V E D
DI AG NO STICS
CO DE
I R-RE CE IV E R
Set up of the baud rate for communication with a computer.
The communication speed between projector and computer, e.g. PC or MAC, has 8
possible speeds. With DIP switches S2(1,2,3) on the controller unit, it is possible to
select the baud rate (communication speed).
Gaining access to the DIP switches
Power down the projector and unplug the power cord from the wall outlet.
Turn both lock screws with a screwdriver or coin counter clockwise.
Lift up and pivot the top cover. Attention : the cover is not secured with an
incorporated support. When opening, turn it over slowly and lay it down on the
second part of the top cover.
The processor module with the DIP switches is located on top, the front left side
(seen from the front of the projector, see next page).
Loosen the locking
screws.
Open the top cover
R
B
V
R
B
V
100 - 230 V
9 - 4 A
60 - 50 Hz
RS232 OUT
0
I
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) This device may not cause harmful interference
(2) This device must accept any interference received
including interference that may cause undesired operation
I R- A CK NO WL E DG E D
I R- RECE I V E D
DI AG NO STICS
CO DE
I R-RE CE IV E R
R
B
V
R
B
V
100 - 230 V
9 - 4 A
60 - 50 Hz
RS232 OUT
0
I
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) This device may not cause harmful interference
(2) This device must accept any interference received
including interference that may cause undesired operation
I R- A CK NO WL E DG E D
I R-RE CE IV E D
DI AG NO STICS
CO DE
I R- RECE I V E R
