manualshive.com logo in svg

Barco BarcoData 2100 LC, Installation Manual

Share
Download
Barco BarcoData 2100 LC Installation Manual Download Page 6

2-1

Password Set Up

5975349A RETRO BLOCK DATA 2100LC 200598

2

PASSWORD SET UP

How to Enable or Disable the Password

The password function is enabled/disabled when the password

strap plug on the controller circuit board module is installed in the

specified way. To get access to the controller circuit board module,

proceed as follows:

Œ

 Remove top cover of projector as described in point 

Œ

 of the

'voltage adaptation procedure' in Chapter 1 'Power Connection'.

The password strap on the controller circuit board module will

now be visible.



 The strap plug can be seen approximately half way down on the

left side of the circuit board. To change its position just unplug by

pulling it out of its pins. The choice of password function is a user

definable decision!

Ž

a. When the password strap is inserted into the right pin and the

middle pin the password function is 

enabled

.

Ž

b. When the password strap plug is inserted into the left pin and

the middle pin the password function is 

disabled

.

PASSWORD

STRAP

PLUG

CONTROLLER

CIRCUIT

BOARD

MODULE

Once the password strap plug position has been chosen it is

necessary to secure the projector. Follow the instructions in reverse

order to reassemble the projector.

PASSWORD

STRAP PLUG

- ENABLE

PASSWORD

STRAP PLUG

- DISABLE



a.



b.

Summary of Contents for BarcoData 2100 LC












Reviews:

No comments

Brands by name

Popular brands

Load more brands