manualshive.com logo in svg

Barco BarcoData 2100 LC, Installation Manual

Share
Download
Barco BarcoData 2100 LC Installation Manual Download Page 3

i-1

Table of Contents

5975349A RETRO BLOCK DATA 2100LC 200598

i

TABLE OF CONTENTS

TABLE OF CONTENTS......................................................................................................................................................... I-1

POWER CONNECTION ...................................................................................................................................................... 1-1

Power (mains) cord connection .........................................................................................................................................................1-1

Fuses ..................................................................................................................................................................................................1-1

Switching on .......................................................................................................................................................................................1-1

Lamp lifetime .......................................................................................................................................................................................1-2

Switching to stand-by. ........................................................................................................................................................................1-2

Switching off ......................................................................................................................................................................................1-2

PASSWORD SET UP ........................................................................................................................................................... 2-1

How to Enable or Disable the Password ........................................................................................................................................... 2-1

How to Change the Password Menu .................................................................................................................................................2-2

OFF-AXIS PROJECTION ..................................................................................................................................................... 3-1

Off-axis projection ..............................................................................................................................................................................3-1

Adjustment Procedure ........................................................................................................................................................................3-1

Summary of Contents for BarcoData 2100 LC












Reviews:

No comments

Brands by name

Popular brands

Load more brands