![background image](http://html1.mh-extra.com/html/barco/athena/athena_installation-manual_473883013.webp)
R5906790 /04
Athena
13
•
Small glass parts can leave the projector in the event of lamp explosion. Keep 1 m (40 in.) distance from
the air outlet side of the projector during operation.
•
The installation, maintenance or service is for skilled persons only.
•
The requirements for a
restricted access location
and an
exclusion zone
.
Restricted access location
To protect untrained persons and children, the projector must be installed in a
restricted access location
.
The definition of a
restricted access location
is a location for equipment where both of the following
paragraphs apply:
•
Access can only be gained by skilled persons (installer or service personnel) or persons who have been
instructed and trained by a skilled person. The persons must have been instructed about the reasons for
the restriction applied to the location and about the precautions that shall be taken.
•
Access is only possible through the use of the tool or lock and key, or other means of security, and is
controlled by the authority responsible for the location.
Exclusion zone
The projector radiates heat on its external surfaces and from ventilation ducts during normal operation.
Exposing flammable or combustible materials into close proximity of this projector could result in the
spontaneous ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an
exclusion zone around all external surfaces of the projector whereby no flammable or combustible materials
are present:
•
The exclusion zone must not be less than 40 cm (16 in.).
•
Loose papers or other objects may not be nearer to the projector than 10 cm (4 in.) on any side.
•
Rear exhaust: the exclusion zone on the rear side must not be less than 1 m (40 in.).
To protect untrained users and children against high intensity light beams, the light beam Hazard Distance
(HD) shall be taken into account. See
“
Light beam Hazard Distance (HD)
”
, page 16.
2.3 Important safety instructions
To prevent the risk of electrical shock
•
Installation according to the local electrical code and regulations by qualified technical personnel only.
•
A readily accessible disconnect device must be incorporated externally to the equipment for removal of the
power to the projector cord.
•
Warning: High leakage current. Earth connection essential before connecting supply.
•
Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the
cord.
•
Do not operate the projector with a damaged cord or if the projector has been dropped or damaged - until it
has been examined and approved for operation by a qualified service technician.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should
be used. A cord rated for less amperage than the projector may overheat.
•
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous
voltage points or short circuit parts that could result in a risk of fire or electrical shock.
•
Do not expose this projector to rain or moisture.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified
service personnel before resuming operations.
•
Do not disassemble this projector, always take it to a trained service person when service or repair work is
required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended
and unused for long periods of time, remove all power from the projector. This will prevent damage to the
projector due to lightning and AC power-line surges.
Summary of Contents for Athena
