background image

®

January 2022 (v1.5)

3

VARIO W+ OPERATIONS MANUAL

SAFETY INFORMATION

Keep these instructions for future reference. Read the information 
below very carefully as it contains important safety information for 
use of this appliance.

 !

Use only with AC current and the correct voltage. 
See the label on the base of the grinder to 
determine the correct voltage.

 !

Only clean the grinder housing with a dry or slightly 
damp cloth. Do not immerse the grinder, plug or 
cord in water or any other liquid.

 !

Baratza will not accept any liability for damage, 
injury, or warranty if the grinder is used other than 
for its intended purpose (i.e. grinding roasted whole 
coffee beans) or is improperly operated or repaired.

 !

Do not operate the grinder with a damaged cord 
or plug. If the supply cord is damaged, it must be 
replaced by the manufacturer, its service agent 

or similarly qualified persons in order to avoid a 

hazard.

 !

Keep the appliance and its cord out of reach of 
children aged less than 8 years.

 !

Do not leave your grinder unattended while 
turned ON.

 !

This appliance can be used by children aged from 
8 years and above and persons with reduced 
physical, sensory or mental capabilities or lack 
of experience and knowledge if they have been 
given supervision or instruction concerning use 
of the appliance in a safe way and understand the 
hazards involved.

 !

Cleaning and user maintenance shall not be made 
by children without supervision.

 !

Always unplug the grinder from the electrical 
supply before assembling, disassembling or 
cleaning. To unplug, grasp plug and remove from 
the outlet. Never pull on the cord.

CAUTION: ALWAYS unplug the electrical supply cord prior to cleaning the grinder.

Summary of Contents for Vario W+
















Reviews: