background image

®

January 2022 (v1.5)

14

VARIO W+ OPERATIONS MANUAL

UPPER BURR CARRIER REINSTALLATION:

1.  Place the upper burr carrier on top of the grind chamber. It should sit level with the grind 

chamber. It will not thread on properly if it is not level.

2.  Use the burr removal tool to rotate the upper burr carrier counterclockwise to carefully thread it 

into the grind chamber. Threading the upper burr carrier into the grind chamber should be fluid 
with minimal resistance. If the upper burr carrier is difficult to rotate, rotate the upper burr carrier 
clockwise to free it from the threading, make sure it is level and that the threads on both the grind 
chamber and burr holder are free of ground coffee, and try again.

USE OF CLEANING TABLETS

Grinder cleaning tablets are designed to absorb and remove odors and coffee oil residue and should be 
considered supplementary to normal cleaning. Grinder cleaning tablets should be the only substance used 
to clean the internals of the grinder. Note that cleaning tablets do not take the place of normal cleaning 
steps listed above and cannot be used to clear a clog. For grinder tablet cleaning:

1.  Remove all beans from the hopper and use the START/STOP 

(7)

 button to run the grinder to expel 

any coffee that remains in the grinder.

2.  Adjust the grind setting to 10 and place the recommended amount of the chosen cleaning tablets 

into the empty bean hopper. Set the target grind weight equal to or greater than the weight of the 
grinder cleaning tablets. 

3.  Insert the grounds bin, then press the START/STOP button. Grind all the tablets into the bin.
4.  Once complete, we recommend grinding approximately 30g coffee (or the recommended amount 

in the cleaning tablet instructions) to remove any tablet residue.

5.  Discard the ground tablets/coffee.

Summary of Contents for Vario W+
















Reviews: