FLO
W
26
23
19
4
14
29
25
17
15
12
11
10
9
7
4
5
2
21
16
13
30
32
28
24
22
20
18
1
33
31
27
34
35
36
37
38
39
See Valve Functions
Instruction Sheet for
proper valve alignment.
2
3
3
2
4
Filter
Front
Label
32
33
10
11
6
SAVE THESE INSTRUCTIONS
Read all instructions prior to installation
IMPORTANT: Follow all national and local building and safety codes.
Your Baquapure Sand Filter System is shipped with all needed components ready for assembly and installation.
S
AFETY
Warning:
A GFCI is required. System will require a 110Volt / 20 Amp service.
DO NOT
use extension cords. Use will void warranty
on pump motor
. The pool equipment should be located between the pool skimmer and return line. The filtration system should not be installed
less than 2' and no more than 5' from the pool. The Baquapure Sand Filter System needs to be on a completely flat / level surface. (patio block,
cement slab, etc.). Assemble filter system only after above ground pool is installed. Fill pool with water.
Important: Do Not
raise water level
above pool return line or skimmer throat until installation is complete.
Note: Open shipping carton in an upright position, checking con-
tents, as follows:
SEE ENCLOSED WATER POLISHER ASSEMBLY INSTRUCTIONS
1.
Pump and trap assemblies
2.
Pump mounting base
3.
Filter and base
4.
One filter / pump hose
5.
Two corrugated hoses
6.
One fittings bag
7. One
Collar
Wrench
8.
Water Polisher
9.
Water Polisher Base
R
EPLACEMENT
P
ARTS
Inlet
Pump
Outlet
Pool
Multi-Port Valve Ports
C
LEANING
I
NSTRUCTIONS
Note:
When pressure gauge reading is 5 PSI or higher than original starting pressure, the filter needs to be cleaned. The Baquapure Sand Filter
System features our exclusive 7 Position Multiport Valve, which ensures safe and simple filter maintenance.
Pressurized vessel. Never attempt to loosen or open Collar Assembly, #16, P/N 718-1960 and #17, P/N 819-0015, while system is
running. It could cause severe injury or harm to user.
1. Turn off pump.
2. Attach
Backwash
hose (optional) to waste port adapter.
3. Rotate Multiport Valve handle to
Backwash
position,
Turn pump on
and run for 90 second intervals or until discharge water is clear.
Turn pump off
.
4. Rotate Multiport Valve handle to
Rinse
position.
Turn pump on
for 30 seconds.
5. Repeat steps 3 & 4 until all discharge water is clear while pump is turned on.
6. Rotate Multiport Valve handle to
Filter
position.
Turn pump on
. Valve is now in normal operating position
Item
Part No.
Description
1
LB5501860
22
″
Model, Hose Assembly
LB5501870
26
″
Model, Hose Assembly
2
711-4000
1
1
⁄
2
″
Gasket
3
417-4161
1
1
⁄
2
″
Buttress x 1
1
⁄
2
″
MPT
4
805-0224
O-Ring
5
419-4161
2
″
NPT x 1
1
⁄
2
″
Buttress Coupling
6
902-2000
Teflon Tape
7
CCSS-5000
Water Polisher
8
819-0004
Screw (4) #10x1 PPH
9
CABASE-V
Water Polisher Base
10
600-8171
Check Valve Adapter Assembly
11
872-0011
Hose Clamp, Stainless Steel
12
872-9002
Corrugated Hose, Black
13
830-2000-LB
0-30 PSI Gauge
14
WVS003-BP
Multiport Valve Assembly
15
425-1928
Waste Adapter Fitting
16
505-1970
Collar Wrench
17
505-3010
Split Nut, Sand Filter Assembly
18
819-0015
Screw,
1
⁄
4
″
20 PPH X 2
″
19
820-0013
Hex Nut, Serrated
1
⁄
4
″
20
20
805-0435
O-Ring
21
505-2060
22
″
Lateral and Manifold Assembly
505-2080
26
″
Lateral and Manifold Assembly
Item
Part No.
Description
22
505-3000
Threaded Sleeve for Split Nut
23
LB5152000
22
″
Sand Filter Body
LB5152060
26
″
Sand Filter Body
24
502-2011
Sand Fill Guide
25
505-2020
Drain Assembly
26
505-2030
Drain Cap Assembly
27
820-0017
Washer
3
⁄
8
″
Flat
28
819-0016
Bolt for 22
″,
26
″
Sand Filter
3
⁄
8
″
16x 1
1
⁄
2
″
Hex
29
672-7211
Filter Base
30
672-7201
Pump Base
31
PB2200
2 HP, 2 SPD Baquapure Pump
PB2250
2.5 HP, 2 SPD Baquapure Pump
32
429-7300
Pin & Anchor Assembly
33
711-4010
2
″
Gasket
34
LB5501821
22
″
Sand Filter Hose Assembly
LB5501831
26
″
Sand Filter Hose Assembly
35
319-3230
6
″
Basket Assembly (Not Shown)
36
319-2170
6
″
Pump Trap Body
37
805-0436
O-Ring
38
319-3260
6
″
Pump Trap Lid
39
WV001U
Slice Valve with Gasket
810-0081-LB R8
Instruction Sheet
6
REPLACEMENT PARTS DIAGRAM
Optional for hard plumbing
1
1
⁄
2
″ #7
Union Assembly
1
1
⁄
2
″
Slip Pump end
Not Included
P/N# 400-4060
Pin & Anchor
Assembly
#31
Screw (4)
#10x1 PPH
#8